O. Reg. 201/17: GENERAL
filed June 27, 2017 under Farm Implements Act, R.S.O. 1990, c. F.4
Skip to contentontario regulation 201/17
made under the
Farm Implements Act
Made: June 22, 2017
Filed: June 27, 2017
Published on e-Laws: June 27, 2017
Printed in The Ontario Gazette: July 15, 2017
Amending Reg. 369 of R.R.O. 1990
(GENERAL)
1. (1) Subsection 11 (3) of Regulation 369 of the Revised Regulations of Ontario, 1990 is revoked and the following substituted:
(3) A dealer shall ensure that a rollover protective structure on a tractor manufactured before July 1, 2017 complies with,
(a) the provisions referred to in item 1 of Table 1 to this section in the column that applies to the tractor; or
(b) the provision referred to in item 2 of Table 1 to this section in the column that applies to the tractor and,
(i) the standard referred to in item 3 of Table 1 to this section in the column that applies to the tractor,
(ii) the standard referred to in item 4 of Table 1 to this section in the column that applies to the tractor,
(iii) the standard referred to in item 5 of Table 1 to this section in the column that applies to the tractor, or
(iv) the standard referred to in item 6 of Table 1 to this section in the column that applies to the tractor.
(3.1) A dealer shall ensure that a rollover protective structure on a tractor manufactured on or after July 1, 2017 complies with,
(a) the provisions referred to in item 1 of Table 2 to this section in the column that applies to the tractor; or
(b) the provision referred to in item 2 of Table 2 to this section in the column that applies to the tractor and,
(i) the standard referred to in item 3 of Table 2 to this section in the column that applies to the tractor,
(ii) the standard referred to in item 4 of Table 2 to this section in the column that applies to the tractor,
(iii) the standard referred to in item 5 of Table 2 to this section in the column that applies to the tractor, or
(iv) the standard referred to in item 6 of Table 2 to this section in the column that applies to the tractor.
(2) Clause 11 (4) (c) of the Regulation is revoked and the following substituted:
(c) the standards referred to in subsection (3) or (3.1) with which it complies.
(3) Clauses 11 (5) (a) and (b) of the Regulation are revoked and the following substituted:
(a) section 5 of SAE Standard J1194, entitled “Rollover Protective Structures (ROPS) for Wheeled Agricultural Tractors” and dated April 2009; or
(b) clause 4.4.1, under the heading “Seat belts”, from CSA Standard B352.0-16 entitled “Rollover protective structures (ROPS), falling object protective structures (FOPS), operator protective structures (OPS), and tip-over protective structures (TOPS) for mobile machinery — General Canadian requirements” and dated July 2016.
(4) The Table to section 11 of the Regulation is revoked and the following substituted:
Table 1
Tractors Manufactured before July 1, 2017
|
Item |
Description of Standard |
Tractor manufactured on or before December 31, 2005 |
Tractor manufactured from January 1, 2006 to June 30, 2010 |
Tractor manufactured from July 1, 2010 to June 30, 2017 |
|
1. |
Requirements for ROPS on Agricultural Tractors |
Clause 5 of CSA Standard B352.1-95, entitled “Rollover Protective Structures (ROPS) for Agricultural, Construction, Earthmoving, Forestry, Industrial, and Mining Machines — Part 2: Testing Requirements for ROPS on Agricultural Tractors” dated August 1995 (Reaffirmed 2004) |
Clause 5 of CSA Standard B352.1-95, entitled “Rollover Protective Structures (ROPS) for Agricultural, Construction, Earthmoving, Forestry, Industrial, and Mining Machines — Part 2: Testing Requirements for ROPS on Agricultural Tractors” dated August 1995 (Reaffirmed 2006) |
Clause 5 of CSA Standard B352.1-95, entitled “Rollover Protective Structures (ROPS) for Agricultural, Construction, Earthmoving, Forestry, Industrial, and Mining Machines — Part 2: Testing Requirements for ROPS on Agricultural Tractors” dated August 1995 (Reaffirmed 2006) |
|
2. |
Rollover Protective Structure Steel Material / Test Temperature Requirements |
Clause 4.2 of CSA Standard B352.0-95, entitled “Rollover Protective Structures (ROPS) for Agricultural, Construction, Earthmoving, Forestry, Industrial, and Mining Machines — Part 1: General Requirements for ROPS” dated September 1995 (Reaffirmed 2004) |
Clause 4.2 of CSA Standard B352.0-95, entitled “Rollover Protective Structures (ROPS) for Agricultural, Construction, Earthmoving, Forestry, Industrial, and Mining Machines — Part 1: General Requirements for ROPS” dated September 1995 (Reaffirmed 2006) |
Clause 4.2 of CSA Standard B352.0-09, entitled “Roll-over protective structures (ROPS), falling object protective structures (FOPS), operator protective structures (OPS), and tip-over protective structures (TOPS) for mobile machinery — General Canadian requirements” dated September 2009 (Reaffirmed 2014), as amended from time to time up to the date of manufacture |
|
3. |
Static Test Method and Acceptance Conditions |
ISO Standard 5700-1989 (Third edition), entitled “Wheeled tractors for agriculture and forestry — Protective structures — Static test method and acceptance conditions”, published in 1989 and amended in 1998
|
ISO Standard 5700:2006, entitled “Tractors for agriculture and forestry — Roll-over protective structures (ROPS) — Static test method and acceptance conditions” published in 2006 |
ISO Standard 5700:2006, entitled “Tractors for agriculture and forestry — Roll-over protective structures (ROPS) — Static test method and acceptance conditions” published in 2006, as amended from time to time up to the date of manufacture |
|
4. |
Dynamic Test Method and Acceptance Conditions |
ISO Standard 3463-1989 (Third edition), entitled “Wheeled tractors for agriculture and forestry — Protective structures — Dynamic test method and acceptance conditions”, published in1989 and amended in 1998 |
ISO Standard 3463:2006, entitled “Tractors for agriculture and forestry — Roll-over protective structures (ROPS) — Dynamic test method and acceptance conditions” published in 2006 |
ISO Standard 3463:2006, entitled “Tractors for agriculture and forestry — Roll-over protective structures (ROPS) — Dynamic test method and acceptance conditions” published in 2006, as amended from time to time up to the date of manufacture |
|
5. |
International Standards |
SAE Standard J2194, entitled “Roll-Over Protective Structures (ROPS) for Wheeled Agricultural Tractors” dated August 2002 |
SAE Standard J2194, entitled “Roll-Over Protective Structures (ROPS) for Wheeled Agricultural Tractors” dated August 2002 |
SAE Standard J2194, entitled “Roll-Over Protective Structures (ROPS) for Wheeled Agricultural Tractors” dated August 2002, as amended from time to time up to the date of manufacture |
|
6. |
International Standards |
Code 3 (Dynamic Test), dated February 2002, or Code 4 (Static Test), dated February 2002, of the Organization for Economic Co-operation and Development Standard Code for the Official Testing of Protective Structures on Agricultural and Forestry Tractors. |
Code 3 (Dynamic Test), dated February 2002, or Code 4 (Static Test), dated February 2002, of the Organization for Economic Co-operation and Development Standard Code for the Official Testing of Protective Structures on Agricultural and Forestry Tractors. |
Code 3 (Dynamic Test), dated February 2002, or Code 4 (Static Test), dated February 2002, of the Organization for Economic Co-operation and Development Standard Code for the Official Testing of Protective Structures on Agricultural and Forestry Tractors, as amended from time to time up to the date of manufacture. |
Table 2
Tractors Manufactured on or after July 1, 2017
|
Item |
Description of Standard |
Tractor manufactured on or after July 1, 2017 |
|
1. |
Requirements for ROPS on Agricultural Tractors |
CSA Standard B352.0-16, entitled “Rollover protective structures (ROPS), falling object protective structures (FOPS), operator protective structures (OPS), and tip-over protective structures (TOPS) for mobile machinery — General Canadian requirements” published in 2016, as amended from time to time up to the date of manufacture |
|
2. |
Rollover Protective Structure Steel Material / Test Temperature Requirements |
Clause 4.2 of CSA Standard B352.0-16, entitled “Rollover protective structures (ROPS), falling object protective structures (FOPS), operator protective structures (OPS), and tip-over protective structures (TOPS) for mobile machinery — General Canadian requirements” published in 2016, as amended from time to time up to the date of manufacture |
|
3. |
Static Test Method and Acceptance Conditions |
CSA Standard CAN/CSA - M5700-09, entitled “Tractors for agriculture and forestry — Roll-over protective structures (ROPS) — Static test method and acceptance conditions” published in 2009 (Reaffirmed 2015), as amended from time to time up to the date of manufacture |
|
4. |
Dynamic Test Method and Acceptance Conditions |
CSA Standard CAN/CSA - M3463-09, entitled “Tractors for agriculture and forestry — Roll-over protective structures (ROPS) — Dynamic test method and acceptance conditions” published in 2009 (Reaffirmed 2014), as amended from time to time up to the date of manufacture |
|
5. |
International Standards |
SAE Standard J2194, entitled “Roll-Over Protective Structures (ROPS) for Wheeled Agricultural Tractors” dated August 2002, as amended from time to time up to the date of manufacture |
|
6. |
International Standards |
Code 3 (Dynamic Test), dated February 2002, or Code 4 (Static Test), dated February 2002, of the Organization for Economic Co-operation and Development Standard Code for the Official Testing of Protective Structures on Agricultural and Forestry Tractors, as amended from time to time up to the date of manufacture. |
2. (1) Subsection 11.1 (2) of the Regulation is amended by striking out “On and after June 15, 2005” at the beginning and substituting “On and after June 15, 2005 but before July 1, 2017”.
(2) Section 11.1 of the Regulation is amended by adding the following subsection:
(2.1) On and after July 1, 2017, every tractor or other self-propelled farm implement with an instructional seat that is sold or offered for sale by a dealer shall comply with the CSA Standard CAN/CSA-M23205:12 entitled Agricultural tractors — Instructional seat and published in 2012, as amended from time to time up to the date of the sale or offer.
Commencement
3. This Regulation comes into force on the later of July 1, 2017 and the day it is filed.
Le ministre de l'Agriculture, de l'Alimentation et des Affaires rurales,
Jeff Leal
Minister of Agriculture, Food and Rural Affairs
Date made: June 22, 2017
Pris le : 22 juin 2017