Part I - General

Part I .1 - Definitions

Rule 1. In these rules,

1. the following definitions apply:

“Act”
means the Clean Water Act, 2006;
“agricultural managed land”
means managed land that is used for agricultural production purposes including areas of cropland, fallow land and improved pasture where agricultural source material (ASM), commercial fertilizer or non-agricultural source material (NASM) is applied or may be applied;
“agricultural source material”
has the same meaning as in section 1 of Ontario Regulation (O. Reg.) 276/03 (General) made under the Nutrient Management Act, 2002;
“allocated quantity of water”
means, in respect of an existing surface water intake or an existing well, the existing demand of the intake or well plus any additional quantity of water that would have to be taken by the intake or well to meet its committed demand, up to the maximum quantity of water that can lawfully be taken by the intake or well.
“committed demand”
means a quantity of water, greater than the existing demand, that is necessary to meet the needs of the approved settlement area within an official plan.
“cone of influence”

means,

  1. in respect of one or more wells that draw water from a unconfined aquifer, the area within the depression created in the water table when the wells are pumped at a rate equivalent to their allocated quantity of water; and
  2. in respect of one or more wells that draw water from a confined or semi-confined aquifer, the area within the depression created in the potentiometric surface when the wells are pumped at a rate equivalent to their allocated quantity of water;
“connecting channel”
means the St. Lawrence River, St. Mary’s River, St. Clair River, Detroit River, Niagara River and the Welland Canal;
“Conservation Authority Regulation Limit”
means the areas delineated in accordance with O. Reg. 97/04 (Content of Conservation Authority Regulations Under Subsection 28(1) of the Conservation Authorities Act: Development, Interference with Wetlands and Alterations to Shorelines and Watercourses) for the purpose of describing the areas where development is prohibited unless a person obtains a permission under section 28 of the Act;
“consumptive activity”
means an activity that takes water from an aquifer or a surface water body without returning the water taken to the same aquifer or surface water body;
“Director”
means a director appointed for the purpose of section 107 of the Act;
“drinking water”
has the same meaning as in the Safe Drinking Water Act, 2002;
“existing demand”
means the quantity of water determined to be currently taken from an existing surface water intake or an existing well during the study period.
“extreme event”

means,

  1. a period of heavy precipitation or winds up to a 100 year storm event;
  2. a freshet; or
  3. a surface water body exceeding its high water mark;
“farm unit”
has the same meaning as in section 1 of O. Reg. 267/03 (General) made under the Nutrient Management Act, 2002;
“future development”
means the development of an area in accordance with the official plans applicable to the area to an extent that would have the most significant impact on the quality of water used for drinking water purposes and the quantity of water available from sources of drinking water;
“geographic information system”
means a computer based system that has the capability to input, store, retrieve, manipulate, analyze, and output geographically referenced data;
“Great Lakes agreement”
means an agreement to which subsection 14(1) of the Act applies;
“land cover”
means the physical and biological cover on the land, including vegetation and anthropogenic features;
“local area”

means,

  1. in respect of a surface water intake, the drainage area that contributes surface water to the intake and the area that provides recharge to an aquifer that contributes groundwater discharge to the drainage area; and
  2. in respect of a well, the area that is created by combining all of the following areas:
    1. the cone of influence of the well;
    2. the cones of influence resulting from other water takings where those cones of influence intersect that of the well;
    3. the areas outside the combined cones of influence where a future reduction in recharge would have a measurable impact on the wells; and
    4. the surface water drainage area upstream of, and including, a losing reach of a stream that contributes a significant proportion of surface water to the wells.
“managed land”
means land to which agricultural source material, commercial fertilizer or non-agricultural source material is applied;
“non-agricultural source material”
has the same meaning as in section 1 of O. Reg. 276/03 (General) made under the Nutrient Management Act, 2002;
“nutrient unit”
has the same meaning as in section 1 of O. Reg. 267/03 (General) made under the Nutrient Management Act, 2002;
“Nutrient Management Protocol”
has the same meaning as in section 1 of O. Reg. 267/03 (General), made under the Nutrient Management Act, 2002;
“official plan”
means an official plan prepared in accordance with part III of the Planning Act;
“Ontario Drinking Water Quality Standards”
means O. Reg. 169/03 (Ontario Drinking Water Quality Standards) made under the Safe Drinking Water Act, 2002;
“planned demand”
means a specific quantity of water that is required to meet the projected growth identified within a master plan or class environmental assessment, but is not already linked to growth within an official plan.
“planned quantity of water”

means,

  1. in respect of an existing surface water intake or existing well, any amount of water that meets the definition of a planned system in O. Reg. 287/07 and any amount of water that is needed to meet a committed demand above the maximum quantity of water that can lawfully be taken by the intake or well.
  2. in respect of a new planned surface water intake or planned well, any amount of water that meets the definition of a planned system in O. Reg. 287/07.
“Regulation Limit”
Removed and replaced with “Conservation Authority Regulation Limit”;
“river”
includes a creek, stream, brook and any similar watercourse but does not include a connecting channel;
“Soil, Ground Water and Sediment Standards”
means the drinking water component of those standards (which assists in determining whether a ground water supply is a suitable source of drinking water and is referred to as “GW1” or “S-GW1”), as described in the Ministry of the Environment and Climate Change publication entitled “Rationale For The Development of Soil and Groundwater Standards for Use at Contaminated Sites in Ontario” under “Soil, Ground Water and Sediment Standards for Use under Part XV.1 of the Environmental Protection Act” dated April 15, 2011, or as amended from time to time;
“study year”
Deleted.
“study period”
means the period during which data is available in relation to the current, representative water demand of an existing drinking water system;
“subwatershed”
means an area that is drained by a tributary or some defined portion of astream;
“surface soil”
means soil that is no more than 1.5 metres beneath the soil surface but does not include soil beneath any non-soil surface treatment including asphalt, concrete or aggregate;
“Tables of Drinking Water Threats”
means the Ministry of the Environment publication "Table of Drinking Water Threats: Clean Water Act, 2006 " dated December 12, 2008, as amended from time to time;
“Technical Support Document for Ontario Drinking Water Standards, Objectives and Guidelines”
means the Ministry of the Environment publication of that name dated June 2003 as amended June 2006;
“ten year drought period”
means the continuous ten year period for which precipitation records exist with the lowest mean annual precipitation;
“Tier One”
in respect of a water budget means a water budget developed using a geographical information system or equivalent to assess groundwater flows and levels, surface water flows and levels, and the interactions between them;
“Tier Two”
in respect of a water budget means a water budget developed using computer based three dimensional groundwater flow models and computer based continuous surface water flow models to assess groundwater flows and levels, surface water flows and levels, and the interactions between them;
“Tier Three”

in respect of a water budget means a water budget developed using computer based three dimensional groundwater flow models and computer based continuous surface water flow models to assess groundwater flows and levels, surface water flows and levels, and the interactions between them, and that includes consideration of the following circumstances:

  1. current and future land cover within the area;
  2. hydraulic flow controls within the area;
  3. water taken by the surface water intakes and wells related to the area;
  4. other uses of water within and downstream of the area;
  5. steady and transient states in groundwater;
  6. drought conditions;
  7. the average daily supply and demand for surface water within the area; and
  8. average monthly supply and average monthly demand for groundwater within the area;
“time of travel”

means,

  1. in respect of groundwater, the length of time that is required for groundwater to travel a specified horizontal distance in the saturated zone; and
  2. in respect of surface water, the length of time that is required for surface water to travel a specified distance within a surface water body;
“transport pathway”
in respect of an intake protection zone means works or any other thing that reduces the time it takes for a contaminant to reach a surface water intake and may include storm sewers, discharge pipes, utility trenches, ditches, swales, drainage works or any other types of drains;
“total impervious surface area”
in respect of subrule 16 (11) means the surface area of all highways and other impervious land surfaces used for vehicular traffic and parking, and all pedestrian paths;
“two year or greater drought period”

means,

  1. in relation to an assessment of surface water quantity, the continuous period, consisting of at least two years, for which precipitation records exist with the lowest mean annual precipitation, or
  2. in relation to an assessment of groundwater quantity, a simulated period, consisting of at least two years with no groundwater recharge;
“type I system”
means a drinking water system described in subclause 15(2)(e)(i) of the Act;
“type II system”
means a drinking water system described in subclause 15(2)(e)(ii) of the Act;
“type III system”
means a drinking water system described in subclause 15(2)(e)(iii) of the Act; and
“water taking”
has the same meaning as in the Ontario Water Resources Act;

2. the following equation shall be used where these rules require the calculation of a percent water demand in relation to groundwater:

%Water Demand (Groundwater) = (QDemand) ÷ (QSupply − QReserve) × 100 QDEMAND (Groundwater Consumptive Use)
Calculation: Groundwater consumptive use is calculated as the portion of estimated average annual and monthly rate of groundwater takings in a subwatershed that is not returned to the aquifer that is the source of the water taking;

QSUPPLY (Groundwater Supply)
Calculation: Groundwater supply is calculated as the groundwater recharge plus the groundwater inflow into a subwatershed. Recharge can be estimated by multiplying the average subwatershed recharge rate by the area of a subwatershed.

QRESERVE (Groundwater Reserve)
Calculation: Groundwater reserve is calculated as 10% of the estimated average annual groundwater discharge rate, if available, or if such information is not available to make such a calculation, 10% of the estimated annual groundwater supply (QSupply);

3. the following equation shall be used where these rules require the calculation of a percent water demand in relation to surface water:

%Water Demand (Surface water) = (QDemand) ÷ (QSupply − (QReserve) × 100

QDEMAND (Surface Water Consumptive Use)
Calculation: Surface Water Consumptive Use is calculated as the portion of estimated monthly surface water takings in a subwatershed that is not returned to the surface water body that is the source of the water taking;

QSUPPLY (Surface Water Supply)
Calculation: Monthly surface water supply is calculated by determining the monthly median flow of a surface water body. Where median flow conditions cannot be determined, best available monthly baseflow measurements or estimates should be used;

QRESERVE (Surface Water Reserve)
Calculation: Surface water reserve is calculated by determining the lower decile stream flow (Qp90) on a monthly basis. The lower decile stream flow is the stream flow value that is exceeded 90% of the time. Where measured or modeled stream flow data is not available, an equivalent method may be used.

4. Where these rules refer to the “high water mark” of a surface water body,

  1. the “high water mark” shall be determined in accordance with the method described in the document entitled “Fish Habitat & Determining the High Water Mark on Lakes”, Fact Sheet T-6, published in 2005 by Fisheries and Oceans Canada, as it may be amended from time to time; or
  2. in circumstances where there is insufficient data on the water levels or elevations of a surface water body to use the method described in Fact Sheet T-6 to determine the high water mark, a method that is substantially equivalent to the method described in the Fact Sheet shall be used to establish the high water mark for that surface water body.*

5. If a source protection authority is undertaking work in relation to an amendment to the assessment report portion of a source protection plan, a reference in these rules to “source protection committee” shall be read as the “source protection authority”.

Part I.2 - Assessment report contents

Watershed characterization

Rule 2. The watershed shall be described for the purposes of paragraph 1 of subsection 13(1) of O. Reg. 287/07 (General) in accordance with Part II.

Water budget

Rule 3. Subject to rule 4, a water budget set out for the purpose of clause 15(2)(c) of the Act shall be completed as follows:

  1. prepare a conceptual water budget for every watershed in accordance with Part III.1; and
  2. prepare a water budget for every subwatershed in the source protection area in accordance with Part III.2.

* Amended in March 2017:

Under the method described in Fact Sheet T-6, the high water mark (“HWM”) for a surface water body is calculated as the 80th percentile elevation for the month in which the highest annual water level occurs. For Great Lakes and Connecting Channels, the 80 percentile has been determined by Department of Fisheries and Oceans Canada (DFO) and those elevations are indicated in Fact Sheet T-6.

For inland rivers and streams, where the 80th percentile is not available or the length of records of water levels is not sufficient to calculate the HWM, the HWM would be equivalent to the “bank full level” for the river or stream (the water level at which a stream or river is at the top of its banks without flooding which corresponds to 1.5 -2 years flood event) or its “active channel” (sometimes referred to as the “ordinary high water mark”).

For inland lakes where the 80th percentile is not available or the length of records of water levels is not sufficient to calculate the HWM, the HWM would be determined as the mark where the lake is frequently flooded and leaves a mark on the land. For inland “regulated rivers” (the levels of rivers are regulated by hydraulic structures such as dams) the HWM is determined as the normal high operating water levels of the hydraulic structures.

For any other circumstances where the HWM elevations are not available and not addressed in this footnote, another method may be used that is substantially equivalent to the method described herein.

Rule 4. An area represented by a conceptual water budget or water budget prepared in accordance with rule 3 shall not include any part of a surface water body that is a Great Lake, a connecting channel, Lake Simcoe, Lake Nipissing, Lake St.Clair or the Ottawa River.

Vulnerable area delineation

Rule 5. The identification of vulnerable areas for the purposes of clauses 15(2)(d) and 15(2)(e) of the Act shall be completed as follows:

  1. prepare a qualitative description of the physical geology and hydrodynamic settings across the source protection area, including information to support the delineation of significant groundwater recharge areas, highly vulnerable aquifers and wellhead protection areas;
  2. assess and delineate areas of groundwater vulnerability in accordance with Part IV;
  3. delineate highly vulnerable aquifers, significant groundwater recharge areas and wellhead protection areas in accordance with Part V; and
  4. delineate surface water intake protection zones in accordance with Part VI.

Drinking water issues

Rule 6. The description of drinking water issues for the purpose of clause 15(2)(f) of the Act shall be completed in accordance with Part XI.1.

Drinking water threats

Rule 7. The listing of drinking water threats for each vulnerable area for the purpose ofclause 15(2)(g) of the Act shall be completed as follows:

  1. For every local area for which Part III.2 requires a water budget to be prepared, assign a risk level associated to the area in accordance with Part IX.
  2. List those activities that are determined to be activities that are or would be drinking water threats in relation to water quantity in accordance with Part X.1.
  3. List those activities that are determined to be activities that are or would be drinking water threats in relation to water quality in accordance with Part XI.2.
  4. List those conditions that result from past activities that are determined to be drinking water threats in relation to water quality in accordance with Part XI.3.

Significant, moderate or low drinking water threats

Rule 8. The identification of the areas within vulnerable areas where an activity is or would be a significant, moderate or low drinking water threat for the purpose of subclause 15(2)(h)(i) of the Act and subparagraphs 2i and 2ii of subsection 13(1) of O. Reg. 287/07 (General) and where a condition that results from past activities is a significant, moderate or low drinking water threat for the purpose of subclause 15(2)(h)(ii) and subparagraphs 2iii and 2iv of subsection 13(1) of Reg. 287/07 (General) shall be completed as follows:

  1. Assign vulnerability scores to highly vulnerable aquifers, significant groundwater recharge areas and wellhead protection areas in accordance with Part VII.
  2. Assign vulnerability scores to surface water intake protection zones in accordance with Part VIII.
  3. Identify those areas where activities listed as drinking water threats in relation towater quantity in accordance with Part X.1 are or would be significant or moderate drinking water threats in accordance with Part X.2.
  4. Identify those areas where activities listed as drinking water threats in relation to water quality in accordance with Part XI.2 are or would be significant, moderate or low drinking water threats in accordance with Part XI.4.
  5. Identify those areas where conditions that result from past activities and that are listed as drinking water threats in accordance with Part XI.3 are significant, moderate or low drinking water threats in accordance with Part XI.5.

Minimum information

Rule 9. An assessment report shall include the following:

  1. One or more maps, graphics or tables detailing the following:
    1. The elements required to be included in a characterization of a watershed in accordance with Part II.
    2. The component elements of the water budget for the source protection area that are listed in rule 19.
    3. The location or distribution of the following within the source protection area:
      1. Areas of groundwater vulnerability determined in accordance with Part IV.1.
      2. Vulnerable areas delineated in accordance with Parts V and VI.
      3. Drinking water systems and their related surface water intake protection zones and wellhead protection areas.
      4. Vulnerability scores for areas within vulnerable areas assigned in accordance with Part VII and VIII.
      5. Subwatersheds delineated and stress levels assigned to subwatersheds in accordance with Part III.3 and Part III.4.
      6. Risk levels assigned to local areas in accordance with Part IX.1.
      7. Removed.
      8. Source vulnerability factors and area vulnerability factors for areas within surface water intake protection zones.
      9. Areas determined in accordance with Parts X and XI.4 to be areas within vulnerable areas where activities listed as drinking water threats in accordance with Parts X and XI.2 are or would be significant, moderate or low drinking water threats.
      10. Areas determined in accordance with Part XI.5 to be areas within vulnerable areas where conditions resulting from past activities listed as drinking water threats in accordance with Part XI.3 are significant, moderate or low drinking water threats.
      11. Areas within a vulnerable area where drinking water threats listed in accordance with rule 118 or 119 may contribute to a parameter or pathogen associated with a drinking water issue described in accordance with rule 114.
      12. Drinking water issues and the related information described in rules 114 and 115.
    4. Activities that are or would be and conditions resulting from past activities that are drinking water threats and their respective hazard rating provided by the Director if one is required to be determined in accordance with rule 120, 121, or 139.
    5. The number of locations at which an activity that is a significant drinking water threat is being engaged in.
    6. The number of locations at which a condition resulting from a past activity is a significant drinking water threat.
  2. A written description of the work undertaken in accordance with these rules including,
    1. information sources for data used in developing the assessment report and the purposes for which information was used,
    2. methods of analysis applied to the data,
    3. any limitations in respect of (a) and (b),
    4. the component elements of the water budget for the source protection area that are listed in Part III.1 and the interrelationships between those elements,
    5. with respect to the assessment of the climate of the source protection area undertaken in accordance with Part III.1, the effects that projected changes in the climate over the following 25 years will have on the conclusions reached in the assessment report and a list of the information sources underlying those projected changes,
    6. a description of every uncertainty analysis conducted in accordance with these rules and the results of that analysis, and
    7. a description of how the Great Lakes agreements were considered in the work undertaken, if the source protection area contains water that flows into the Great Lakes or the St. Lawrence River.
  3. Tables listing with respect to the source protection area:
    1. The quality of groundwater and surface water across the area.
    2. The results of every calculation, assessment and assignment required by Parts III.3, III.4 and IX.
    3. Conditions resulting from past activities that are drinking water threats.
    4. Stress levels assigned to subwatersheds and risk levels assigned to local areas.

Part I.3 - General

Method and models

Rule 10. A method or model used in the preparation of the assessment report shall be representative of the area or thing under study.

No assessment of risk management measures

Rule 11. Where these rules provide for or require an assessment of risk for the purpose of listing a drinking water threat in accordance with clause 15(2)(g) of the Act or for the purpose of identifying an area where a drinking water threat may be a significant, moderate or low drinking water threat in accordance with 15(2)(h) of the Act and subsection 13(1) of O. Reg. 287/07 (General), the assessment does not and shall not include consideration of any riskmanagement measures.

Map standards

Rule 12. Maps submitted in an assessment report shall,

  1. include a title, scale bar and a compass rose indicating north;
  2. include a legend using symbols in accordance with the Ministry of Natural Resources publication “Mapping Symbology for the Clean Water Act”, dated November 2008, as amended from time to time; and
  3. be uncluttered and have such large and clear typeface and symbols that they remain legible upon being reduced to one half of their original size.

Part I.4 - Uncertainty analysis – water quality

Rule 13. An analysis of the uncertainty, characterized by “high” or “low” shall be made inrespect of the following:

  1. The assessment of the vulnerability of groundwater throughout the area undertaken in accordance with Part IV.
  2. The delineation of highly vulnerable aquifers, significant groundwater recharge areas and wellhead protection areas undertaken in accordance with Part V.
  3. The delineation of surface water intake protection zones undertaken in accordance with Part VI.
  4. The assessment of the vulnerability of surface water intake protection zones undertaken in accordance with Part VIII.
  5. The assessment of the vulnerability of significant groundwater recharge areas, highly vulnerable aquifers and wellhead protection areas undertaken in accordance with Part VII.

Rule 14. The following factors shall be considered in an analysis conducted for the purpose of rule 13:

  1. The distribution, variability, quality and relevance of data used in the preparation ofthe assessment report.
  2. The ability of the methods and models used to accurately reflect the flow processes in the hydrological system.
  3. The quality assurance and quality control procedures applied.
  4. The extent and level of calibration and validation achieved for models used or calculations or general assessments completed.
  5. For the purpose of subrule 13(1), the accuracy to which the groundwater vulnerability categories effectively assess the relative vulnerability of the underlying hydrogeological features.
  6. For the purpose of subrule 13(4), the accuracy to which the area vulnerability factor and the source vulnerability factor effectively assesses the relative vulnerability of the hydrological features.

Rule 15. An uncertainty factor of “high” or “low” shall be assigned to each vulnerable area delineated based on the results of the analysis conducted under rule 13.

Part I.5 – Alternate methods or approaches

Rule 15.1 Despite any provision of these rules, in preparing an assessment report a source protection committee may use an alternate method or approach for gathering information or for performing a task that departs from the method or approach prescribed in these rules if the following conditions are met:

  1. The assessment report includes,
    1. a rationale for the departure; and
    2. an explanation of how the method or approach used by the source protection committee to gather information or perform the task is equivalent to or better than the approach or method prescribed in these rules.
  2. The Director has provided the source protection committee with written confirmation that he or she agrees to the departure and a copy of the confirmation is included in the assessment report.

Rule 15.2 For greater certainty, section 15.1 does not relieve the source protection committee from ensuring that an assessment report is prepared in accordance with an applicable requirement in the Act, the regulations or the terms of reference.

Part I.6 – Climate data – director’s directions

Rule 15.3 If, in preparing an assessment report, the source protection committee is required by these rules to consider climate data in making a determination or performing a task, the Director may give directions to the committee for the purpose of ensuring that impacts from climate change are taken into account, including directing the committee to,

  1. use a climate data set provided by the Director; or
  2. use any climate data gathered by the committee in the manner specified by the Director.

Part II – Watershed characterization

Rule 16. The following shall be included in a characterization of a watershed, where the information is available:

  1. The boundaries of the watershed.
  2. The following areas within the watershed:
    1. Subwatersheds.
    2. Areas of settlement, as defined in the Places to Grow Act, 2005.
    3. Municipal boundaries, and their population and population density.
    4. Reserves as defined in the Indian Act (Canada), and their population and population density.
    5. Federal lands.
  3. With respect to drinking water systems,
    1. the location and area served by a system,
    2. the classification of the system into the following classifications as defined by O. Reg. 170/03 (Drinking Water Systems) made under the Safe Drinking Water Act, 2002:
      1. Large municipal residential system.
      2. Small municipal residential system.
      3. Large municipal non-residential system.
      4. Small municipal non-residential system.
      5. Non-municipal year-round residential system.
      6. Non-municipal seasonal residential system.
      7. Large non-municipal non-residential system.
      8. Small non-municipal non-residential system.
    3. the number of users served by the system,
    4. the location of surface water intakes and wells that are part of the system, and their average annual and average monthly pumping rates, and
    5. the location of monitoring wells related to the system.
  4. The location and types of natural vegetative cover, including wetlands, woodlands and vegetated riparian areas, and the percentage of land coverage of each type.
  5. The location and types of aquatic habitats, including coldwater, mixed, and warm water fisheries, and macroinvertebrate communities.
  6. A comparison of the communities described in clause (5) to similar communities not impacted by anthropogenic factors.
  7. A description of Species within the source protection area that are on the Species at Risk in Ontario List as defined in the Endangered Species Act, 2007, if the source protection committee is of the opinion that the watershed characterization should include a discussion for the purposes of informing the public about species at risk in the source protection area.
  8. Surface water quality and groundwater quality across watersheds.
  9. One or more maps of the percentage of managed lands within,
    1. a significant groundwater recharge area;
    2. a highly vulnerable aquifer;
    3. each of the following areas within a vulnerable area:

      If two or more areas in an area referred to in clause (a) to (c) have different vulnerability scores, the percentage of managed land may be determined for each of those areas.
      Mapping the percentage of managed lands is not required for any area in an area mentioned in clause (a) to (c) where the vulnerability scores for that area are less than those necessary for the following activities to be considered a significant, moderate or low drinking water threat in the Table of Drinking Water Threats: the application of agricultural source material to land, the application of non-agricultural source material to land and the application of commercial fertilizer to land. Each map prepared in accordance with this subrule shall be labelled the "managed land map".

      1. Wellhead Protection Area (WHPA)-A.
      2. WHPA-B.
      3. WHPA-C.
      4. WHPA-C1, if any.
      5. WHPA-D.
      6. WHPA-E.
      7. Intake Protection Zone (IPZ)-1.
      8. IPZ-2.
      9. IPZ-3, if any.
  10. One or more maps of livestock density for each area referred to in subrule (9). Livestock density shall be determined by dividing the nutrient units generated in each area by the number of acres of agricultural managed land in that area where agricultural source material is applied. If two or more areas in an area referred to in subrule (9) (a) to (c) have different vulnerability scores, the livestock density may be determined for each of those areas. Mapping livestock density is not required for any area in an area mentioned in clause (9)(a) to (c) where the vulnerability scores for that area are less than those necessary for the following activities to be considered a significant, moderate or low drinking water threat in the Table of Drinking Water Threats: the application of agricultural source material to land, the application of non-agricultural source material to land and the application of commercial fertilizer to land. Each map prepared in accordance with this subrule shall be labelled the "livestock density map".
  11. For each vulnerable area, one or more maps of the percentage of the impervious surface area where road salt can be applied per square kilometre in the vulnerable area. Mapping the percentage of impervious surface area is not required for an area in a vulnerable area where the vulnerability scores for that area is less than the vulnerability score necessary for the application of road salt to be considered a significant, moderate or low threat in the Table of Drinking Water Threats. Each map prepared in accordance with this subrule shall be labelled the "total impervious surface area map".

Rule 17. For the purposes of subrule 16(11), the location of a square kilometre in avulnerable area shall be determined by overlaying a 1 kilometre by 1 kilometre grid over the vulnerable area with a node of the grid centred on the centroid of the source protection area.

Rule 18. Parameters used to assess the quality of groundwater and surface water across the watershed shall be selected with consideration given to the natural features and land uses within the source protection area.

Part III – Water budget

Part III.1 - Conceptual water budget

Rule 19. Subject to rule 24, a conceptual water budget shall include an assessment of the following:

  1. Physiography.
  2. Geology.
  3. Surface water bodies and their flows and water levels.
  4. Surface water control structures, including any dams within the meaning of section 1 of the Lakes and River Improvement Act, and any plans that govern operations of the structure.
  5. Groundwater aquifers, their direction of flow, and mapping of the water table and potentiometric surface(s).
  6. Wells and surface water intakes.
  7. Interactions between groundwater and surface water.
  8. In respect of every surface water intake and well for which a permit to take water has been issued under the Ontario Water Resources Act the maximum annual quantity of water that a person is permitted to take under the permit and the purpose for which water is being taken.
  9. How land cover across the area affects groundwater and surface water.
  10. In respect of every surface water intake and well for which a permit to take water has not been issued under the Ontario Water Resources Act, the annual quantity of water taken and the purpose for which water is being taken, including whether water is being taken for a domestic use, agricultural use, commercial use, industrial use or any other specified use.
    • 10.1 In respect of the water takings described in subrules (8) and (10), where available, the actual amounts of water taken annually and the projected annual takings of water
  11. Aquatic habitat dependent upon water depth, flow and temperature.
  12. Trends related to any items listed in subrules (3) to (11).
  13. The climate of the area, including historical trends and existing projections related to changes in the climate of the area.

Part III.2 – Subwatershed water budgets

Rule 20. Subject to rule 24, prepare a Tier One water budget for every subwatershed in the source protection area.

Rule 21. Subject to rule 24, using the data underlying the Tier One water budget for the subwatershed, assign every subwatershed in the source protection area a surface water stress level and a groundwater stress level in accordance with Part III.3.

Rule 22. Subject to rule 24, prepare a Tier Two water budget that,

  1. assigns a surface water stress level for every subwatershed in the source protection area that was assigned a significant or moderate surface water stress level in accordance with rule 21 and from which an existing or planned type I, II or III system takes or will take water from a surface water supply; and
  2. assigns a groundwater stress level for every subwatershed in the source protection area that was assigned a groundwater stress level of significant or moderate in accordance with rule 21 and from which an existing or planned type I, II or III system takes or will take water from a groundwater supply.

Rule 23. Subject to rule 24, using the data underlying the Tier Two water budget for the subwatershed, assign every subwatershed in the source protection area for which a Tier Two water budget has been prepared a surface water stress level and a ground water stress level in accordance with Part III.4.

Rule 24. Rules 19, 20, 21, 22 and 23 do not apply if a water budget was prepared for every subwatershed in the source protection area and those water budgets meet the requirements of a Tier Two water budget and include an assessment of the elements listed in rule 19.

Rule 25. Where rules 19, 20, 21, 22 and 23 do not apply as a result of the application of rule 24, using the data underlying the equivalent Tier Two water budgets described in rule 24, assign every subwatershed in the source protection area from which an existing or planned type I, II or III system takes water a surface water stress level and a ground water stress level in accordance with Part III.4.

Rule 26. Delineate a local area in respect of every surface water intake in the source protection area relating to an existing or planned type I, II or III system that takes water from a subwatershed assigned a surface water stress level of significant or moderate in accordance with rule 23.

Rule 27. Delineate a local area in respect of every well in the source protection area relating to an existing or planned type I, II or III system that takes water from a subwatershed assigned a groundwater stress level of significant or moderate in accordance with rule 23.

Rule 28. Removed.

Rule 29. Removed.

Rule 30. For every local area delineated in accordance with rule 26 or 27, prepare a Tier Three water budget for the local area in accordance with Part IX for the purpose of determining if the local area should be assigned a risk level of significant, moderate or low.

Rule 30.1 If the information required to delineate a local area or to complete a Tier Three water budget in accordance with rule 30 cannot be readily ascertained, the assessment report shall include,

  1. a plan that includes a work schedule for ascertaining the information necessary to delineate the local area or complete the Tier Three water budget, including any additional work that must be carried out under these rules as a result of ascertaining this information; and
  2. if, after completing the work the source protection committee becomes aware that the assessment report is no longer accurate or complete, an estimate of the date by which the source protection committee expects an updated assessment report would be submitted to the Director under section 19 of the Act.

Rule 31. Where the rules in Part III.3 and Part III.4 require that a percent demand calculation is undertaken in relation to a scenario,

  1. the annual percent demand or twelve consecutive monthly percent demands shall be calculated based on the water demand of the study period;
  2. data used to determine demand shall meet the requirements listed in Column 3 of Table 1 where a requirement in respect of all or part of the data is listed, and in all other cases the data shall be reflective of conditions that existed during the most recent period for which data is available and which parallels the duration and starting point of the study period; and
  3. data used to determine supply and reserve shall meet the requirements listed in Column 4 of Table 1 where a requirement in respect of all or part of the data is listed, and in all other cases the data shall be reflective of conditions that existed during the study period.

Part III.3 – Subwatershed stress levels – tier one water budget

Rule 32. For the purposes of rule 21, a subwatershed shall be assigned a surface water stress level of significant, moderate or low in accordance with the following:

  1. Significant, if during scenario A or B in Table 1 the maximum monthly percent water demand for surface water for the subwatershed would be greater than or equal to 50%.
  2. Moderate, if a stress level was not assigned by subrule (1) and one or more of the following circumstances exist:
    1. During scenario A or B in Table 1 the maximum monthly percent water demand for surface water for the subwatershed would be less than 50% but greater than 20%.
    2. At any time after January 1, 1990, in relation to a type I, II or III system within the subwatershed,
      1. any part of a surface water intake was not below the water’s surface during normal operation of the intake, or
      2. the operation of a surface water intake pump was terminated because of an insufficient quantity of water being supplied to the intake.
    3. Both of the following are true:
      1. The result of one or more maximum monthly percent water demand calculations made in accordance with clause (a) of subrule (2) is between 18% and 20%, inclusive.
      2. A sensitivity analysis of the data used to prepare the Tier One Water Budget suggests that the stress level for the subwatershed could be moderate.
  3. Low, if a stress level was not assigned by either subrule (1) or subrule (2).

Rule 33. For the purposes of rule 21, a subwatershed shall be assigned a groundwater stress level of significant, moderate or low in accordance with the following:

  1. Significant, if during scenario A or B in Table 1 one or both of the following circumstances exist:
    1. The annual percent water demand for groundwater for the subwatershed would be greater than or equal to 25%.
    2. The maximum monthly percent water demand for groundwater for the subwatershed would be greater than or equal to 50%.
  2. Moderate, if a stress level was not assigned by subrule (1) and one or more of the following circumstances exist:
    1. During scenario A or B in Table 1 the annual percent water demand for groundwater for the subwatershed would be less than 25% but greater than 10%.
    2. During scenario A or B in Table 1 the maximum monthly percent water demand for groundwater for the subwatershed would be less than 50% but greater than 25%.
    3. At any time after January 1, 1990, in relation to a type I, II or III system within the subwatershed,
      1. the groundwater level in the vicinity of the well was not at a level sufficient for the normal operation of the well, or
      2. the operation of a well pump was terminated because of an insufficient quantity of water being supplied to the well.
    4. Both of the following are true:
      1. The result of one or more annual percent water demand calculations made in accordance with clause (a) of subrule (2) is between 8% and 10%, inclusive.
      2. A sensitivity analysis of the data used to prepare the Tier One Water Budget suggests that the stress level for the subwatershed could be moderate.
    5. Both of the following are true:
      1. The result of one or more maximum monthly percent water demand calculations made in accordance with clause (b) of subrule (2) is between 23% and 25%, inclusive.
      2. A sensitivity analysis of the data used to prepare the Tier One Water Budget suggests that the stress level for the subwatershed could be moderate.
  3. Low, if a stress level was not assigned by either subrule (1) or subrule (2).

Scenario

Description of the Scenario

Data Restrictions Demand

Data Restrictions Supply and Reserve

A  existing system - average  Data related to the study period Data related to climate and stream flow shall be the historical data set for climate and stream flow.
B existing system - future demand  Data related to demand associated with the system within the subwatershed shall be reflective of the future development in the subwatershed.

Data related to climate and stream flow shall be historical data set for climate and stream flow.

Data related to land cover shall be reflective of the future development in the subwatershed.

C planned system demand - operational year  Data related to demand associated with an existing type I, II or III system within the subwatershed shall be reflective of the demand that would exist in the year that the planned system will be operational.

Data set related to climate and stream flow shall be the historical data set for climate and stream flow.

Data related land cover shall be reflective of the year that the planned system will be operational.

D existing system - two year drought  Data related to the study period Data related to climate and stream flow shall be reflective of the two year drought period.
E existing system - future two year drought  Data related to demand associated with an existing type I, II or III system within the subwatershed shall be reflective of the future development in the subwatershed.

Data related to climate and stream flow shall be reflective of the two year drought period.

Data related to land cover shall be reflective of the future development in the subwatershed.

F planned system
- operational year - two year drought
 Data related to demand associated with an existing type I, II or III system within the subwatershed shall be reflective of the demand that would exist in the year that the planned system will be operational.

Data related to climate and stream flow shall be reflective of the two year drought period.

Data related to land cover shall be reflective of the future development that would exist in the subwatershed in the year that the planned system will be operational.

G existing system - ten year drought  Data related to the study period Data related to climate and stream flow shall be reflective of the ten year drought period.
H existing system - future ten year drought  Data related to demand associated with an existing type I, II or III system within the subwatershed shall be reflective of the future development in the subwatershed.

Data related to climate and stream flow shall be reflective of the ten year drought period.

Data related to land cover shall be reflective of the future development in the subwatershed.

 I  Planned system
- operational year - ten year drought
 Data related to demand associated with an existing type I, II or III system within the subwatershed shall be reflective of the demand that would exist in the year that the planned system will be operational.

Data related to climate and stream flow shall be reflective of the ten year drought period.

Data related to land cover shall be reflective of the future development that would exist in the subwatershed in the year that the planned system will be operational.

Part III.4 – Subwatershed stress levels – tier two water budgets

Rule 34. For the purposes of rule 23 or 25, a subwatershed shall be assigned a surface water stress level of significant, moderate or low in accordance with the following:

  1. Significant, if one or both of the following circumstances exist:
    1. During scenario A or B in Table 1 the maximum monthly percent water demand for surface water for the subwatershed would be greater than or equal to 50%.
    2. Where there is a planned type I, II or III system proposed to be located within the subwatershed, during scenario C in Table 1 the maximum monthly percent water demand for surface water for the subwatershed would be greater than or equal to 50%.
  2. Moderate, if a stress level was not assigned by subrule (1) and one or more of the following circumstances exist:
    1. During scenario A or B in Table 1 the maximum monthly percent water demand for surface water for the subwatershed would be less than 50% but greater than 20%.
    2. Where there is a planned type I, II or III system proposed to be located within the subwatershed, during scenario C in Table 1 the maximum monthly percent water demand for surface water for the subwatershed would be less than 50% but greater than 20%.
    3. At any time after January 1, 1990, in relation to a type I, II or III system within the subwatershed,
      1. any part of a surface water intake was not below the water’s surface during normal operation of the intake, or
      2. the operation of a surface water intake pump was terminated because of an insufficient quantity of water being supplied to the intake.
    4. In relation to a type I, II or III system within the subwatershed, one or both of the circumstances described in clause (c) would occur during scenarios D, E, F, G, H or I.
    5. Removed.
    6. All of the following are true:
      1. The result of one or more maximum monthly percent water demand calculations made in accordance with this subrule is between 18% and 20%, inclusive.
      2. The uncertainty associated with the percent demand calculations required by this rule, when evaluated to be high or low considering the factors set out in rule 36, is high.
      3. A sensitivity analysis of the data used to prepare the Tier Two Water Budget suggests that the stress level for the subwatershed could be moderate.
  3. Low, if a stress level was not assigned by either subrule (1) or subrule (2).

Rule 35. For the purposes of rule 23 or 25, a subwatershed shall be assigned agroundwater stress level of significant, moderate or low in accordance with the following:

  1. Significant, if one or more of the following circumstances exist:
    1. During scenario A or B in Table 1 the annual percent water demand for groundwater for the subwatershed would be greater than or equal to 25%.
    2. Where there is a planned type I, II or III system proposed to be located within the subwatershed, during scenario C in Table 1 the annual percent water demand for groundwater for the subwatershed would be greater than or equal to 25%.
    3. During scenario A or B in Table 1 the maximum monthly percent water demand for groundwater for the subwatershed would be greater than or equal to 50%.
    4. Where there is a planned type I, II or III system proposed to be located within the subwatershed, during scenario C in Table 1 the maximum monthly percent water demand for groundwater for the subwatershed would be greater than or equal to 50%.
  2. Moderate, if a stress level was not assigned by subrule (1) and one or more of the following circumstances exist:
    1. During scenario A or B in Table 1 the annual percent water demand for groundwater for the subwatershed would be less than 25% but greater than 10%.
    2. Where there is a planned type I, II or III system proposed to be located within the subwatershed, during scenario C in Table 1 the annual percent water demand for groundwater for the subwatershed would be less than 25% but greater than 10%.
    3. During scenario A or B in Table 1 the maximum monthly percent water demand for groundwater for the subwatershed would be less than 50% but greater than 25%.
    4. Where there is a planned type I, II or III system proposed to be located within the subwatershed, during scenario C in Table 1 the maximum monthly percent water demand for groundwater for the subwatershed would be less than 50% but greater than 25%.
    5. At any time after January 1, 1990 in relation to a type I, II or III system within the subwatershed, one or both of the following circumstances occurred:
      1. The groundwater level in the vicinity of the well was not at a level sufficient for the normal operation of the well.
      2. The operation of a well pump was terminated because of an insufficient quantity of water being supplied to the well.
    6. In relation to a type I, II or III system within the subwatershed, one or both of the circumstances described in clause (e) would occur during scenarios D, E, F, G, H or I.
      1. Removed.
      2. Removed.
    7. Removed.
    8. All of the following are true:
      1. The result of one or more annual percent water demand calculations made in accordance with subclause (a) or (b) of this subrule is between 8% and 10%, inclusive.
      2. The uncertainty associated with the percent demand calculations required by this rule, when evaluated to be high or low considering the factors set out in rule 36, is high.
      3. A sensitivity analysis of the data used to prepare the Tier Two Water Budget suggests that the stress level for the subwatershed could be moderate.
    9. All of the following are true:
      1. The result of one or more maximum monthly percent water demand calculations made in accordance with clause (c) or (d) of subrule (2) is between 23% and 25%, inclusive.
      2. The uncertainty associated with the percent demand calculations required by this rule, when evaluated to be high or low considering the factors set out in rule 36, is high.
      3. A sensitivity analysis of the data used to prepare the Tier Two Water Budget suggests that the stress level for the subwatershed could be moderate.
  3. Low, if a stress level was not assigned by either subrule (1) or subrule (2).

Uncertainty analysis

Rule 36. The following factors shall be considered in an analysis of uncertainty required by subclauses 34(2)(f)(ii) and 35(2)(h)(ii) and 35(2)(i)(ii):

  1. The distribution, variability, quality and relevance of the available input data.
  2. The ability of the methods and models used to accurately reflect the hydrologic system.
  3. The quality assurance and quality control procedures applied.
  4. The extent and level of calibration and validation achieved for any groundwater and surface models used or calculations and general assessments completed.

Part IV – Groundwater vulnerability assessment

Part IV.1 - Vulnerability assessment and delineation, groundwater

Rule 37. The vulnerability of groundwater within a source protection area shall be assessed using one or more of the following groundwater vulnerability assessment methods:

  1. Intrinsic susceptibility index (ISI).
  2. Aquifer vulnerability index (AVI).
  3. Surface to aquifer advection time (SAAT).
  4. Surface to well advection time (SWAT).
  5. Removed.

Rule 38. A source protection area shall be divided into areas of high, medium or low groundwater vulnerability, high corresponding to greater vulnerability, as follows:

  1. Where a method described in subrule 37(1) or (2) was used to assess vulnerability,
    1. areas of high vulnerability are those areas with scores that are less than 30,
    2. areas of medium vulnerability are those areas with scores that are greater than or equal to 30 but less than or equal to 80, and
    3. areas of low vulnerability are those areas with scores that are greater than 80.
  2. Where a method described in subrule 37(3) or (4) was used to assess vulnerability,
    1. areas of high vulnerability are those areas with results that are less than 5 years,
    2. areas of medium vulnerability are those areas with results that are greater than or equal to 5 years but less than or equal to 25 years, and
    3. areas of low vulnerability are those areas with results that are greater than 25 years.
  3. Where, in accordance with rule 15.1, a method that departs from the methods specified in rule 37 has been used to assess vulnerability, an approach shall be used that, in the Director’s opinion, is comparable to the approach specified in subrules (1) and (2).

Rule 38.1 When using a groundwater vulnerability assessment method referred to in subrules 37(3) or (4) to assess the vulnerability of groundwater in a wellhead protection area in respect of a drinking water system mentioned in clause 15(2)(e) of the Act, the shallow and deep aquifer shall be independently assessed and delineated into areas of high, medium or low groundwater vulnerability in accordance with subrule 38(2).

Rule 38.2 If more than one method is used to assess groundwater vulnerability under rule 38.1, the results of both methods must be mapped.

Vulnerability increase, transport pathways

Rule 39. Where the vulnerability of an area identified as low in accordance with rule 38 is increased because of the presence of a transport pathway that is anthropogenic in origin, the area shall be identified as an area of medium or high vulnerability, high corresponding to greater vulnerability.

Rule 40. Where the vulnerability of an area identified as medium in accordance with rule 38 is increased because of the presence of a transport pathway that is anthropogenic in origin, the area shall be identified as an area of high vulnerability.

Rule 41. When determining whether the vulnerability of an area is increased for the purpose of rules 39 and 40 and the degree of the increase, the following factors shall be considered:

  • Hydrogeological conditions.
  • The type and design of any transport pathways.
  • The cumulative impact of any transport pathways.
  • The extent of any assumptions used in the assessment of the vulnerability of the groundwater.

Part V – Delineation of vulnerable areas: highly vulnerable aquifers, significant groundwater recharge areas and wellhead protection areas

Rule 42. Where the rules in this Part require that the extent of an area be determined by timeof travel to a wellhead, one or more of the following models and methods shall be used:

  • A computer based three-dimensional groundwater flow model.
  • Two-dimensional analytical model.
  • Uniform flow method.
  • Calculated fixed radius method.
  • Removed.

Part V.1 - Delineation of highly vulnerable aquifers

Rule 43. An area identified as an area of high groundwater vulnerability in accordance with Part IV and the subsurface beneath that area shall be delineated as a highly vulnerable aquifer.

Rule 43.1 If the vulnerability of a shallow and deep aquifer in a wellhead protection area is assessed and delineated independently in accordance with rule 38.1 the area identified as a shallow aquifer with high groundwater vulnerability in accordance with Part IV shall be delineated as a highly vulnerable aquifer.

Part V.2 - Delineation of significant groundwater recharge areas

Rule 44. Subject to rule 45, an area is a significant groundwater recharge area if,

  • the area annually recharges water to the underlying aquifer at a rate that is greater than the rate of recharge across the whole of the related groundwater recharge area by a factor of 1.15 or more; or
  • the area annually recharges a volume of water to the underlying aquifer that is 55% or more of the volume determined by subtracting the annual evapotranspiration for the whole of the related groundwater recharge area from the annual precipitation for the whole of the related groundwater recharge area.

Rule 45. Despite rule 44, an area shall not be delineated as a significant groundwater recharge area unless the area has a hydrological connection to a surface water body (excluding Great Lakes, Connecting Channels, Lake Simcoe, Lake Nipissing, Lake St. Clair or the Ottawa River) or aquifer that is a source of drinking water for a drinking water system.

Rule 46. The areas described in rule 44 shall be delineated using the models developed for the purposes of Part III of these rules and with consideration of the topography, surficial geology, and how land cover affects groundwater and surface water.

Part V.3 - Delineation of wellhead protection areas, type I systems

Rule 47. A wellhead protection area for a well associated with a type I system is the area created by combining all of the following areas:

  1. Area WHPA-A, being the surface and subsurface area centred on the well with an outer boundary identified by a radius of 100 metres.
  2. Area WHPA-B, being the surface and subsurface areas within which the time of travel to the well is less than or equal to two years but excluding WHPA-A.
  3. Area WHPA-C, being the surface and subsurface areas within which the time of travel to the well is less than or equal to five years but greater than two years.
  4. Area WHPA-D, being the surface and subsurface areas within which the time of travel to the well is less than or equal to twenty-five years but greater than five years.
  5. Area WHPA-E, being the area delineated in accordance with the rules in Part VI that apply to the delineation of an IPZ-2, as if an intake for the system were located,
    1. at the point of interaction between groundwater that is the source of raw water supply for the well and the surface water that is directly influencing that groundwater, or
    2. at the point in the surface water body influencing the raw water supply for the well that is closest in proximity to the well, if the point of interaction described in is not known.
  6. Area WHPA-F, being the area delineated in accordance with the rules in Part VI that apply to the delineation of an IPZ-3, as if an intake for the system were located in the surface water body influencing the well at the point closest in proximity to the well.

Rule 48. Despite rule 47, where a zone representing a ten year time of travel was delineated for the well in a report prepared prior to April 30, 2005 and a five year time of travel has never been delineated for the well the wellhead protection area for a well associated with a type I system is the area created by combining all of the following areas:

  1. Area WHPA-A, delineated in accordance with the requirements of subrule 47(1).
  2. Area WHPA-B, delineated in accordance with the requirements of subrule 47(2).
  3. Area WHPA-C1, being the surface and subsurface areas within which the time of travel to the well is less than or equal to ten years but greater than two years.
  4. Area WHPA-D, being the surface and subsurface areas within which the time of travel to the well is less than or equal to twenty-five years but greater than ten years.
  5. Area WHPA-E, delineated in accordance with the requirements of subrule 47(5).
  6. Area WHPA-F, delineated in accordance with the requirements of subrule 47(6).

Rule 49. Despite subrules 47(5) and 48(5), area WHPA-E shall only be added to awellhead protection area where,

  1. the well obtains water from a raw water supply that is groundwater under the direct influence of surface water as determined in accordance with subsection 2 (2) of O. Reg. 170/03 (Drinking Water Systems) made under the Safe Drinking Water Act,2002;
  2. a determination has not been made under subsection 2(3) of O. Reg. 170/03 (Drinking Water Systems) that subsection 2(2) of that regulation does not apply; and
  3. the interaction between surface water and groundwater has the effect of decreasing the time of travel of water to the well when compared to the time it would take water to travel to the well if the raw water supply for the well was not under the direct influence of surface water.

Rule 50. Despite subrules 47(6) and 48(6), area WHPA-F shall only be added to awellhead protection area where,

  1. the wellhead protection area contains a WHPA-E;
  2. a drinking water issue is identified in accordance with Part XI.1 in relation to the well; and
  3. the source of the drinking water issue described in subrule (2) originates outside of areas WHPA-A, WHPA-B, WHPA-C, WHPA-C1 if any, WHPA-D and WHPA-E.

Rule 50.1 If the information required to delineate a WHPA-E or WHPA-F in accordance with subrule 48(5) or 48(6) cannot be readily ascertained, the assessment report shall include,

  1. a plan that includes a work schedule for ascertaining the information necessary to delineate the WHPA-E and F, including any additional work that must be carried out under these rules as a result of ascertaining this information; and
  2. if, after completing the work the source protection committee becomes aware that the assessment report is no longer accurate or complete, an estimate of the date by which the source protection committee expects an updated assessment report would be submitted to the Director under section 19 of the Act.

Part V.4 - Delineation of wellhead protection areas, type II and III systems

Rule 51. The wellhead protection area for a well associated with a type II and III system to which O. Reg. 170/03 (Drinking Water Systems) made under the Safe Drinking Water Act, 2002, O. Reg. 318/08 (Transitional – Small Drinking Water Systems) made under the Health Protection and Promotion Act or O. Reg. 319/08 (Small Drinking Water Systems) made under the Health Protection and Promotion Act applies, is the area created by combining all of the following areas:

  1. Area WHPA-A, being the surface and subsurface area centred on the well with an outer boundary identified by a radius of 100 metres.
  2. Area WHPA-B, being the surface and subsurface areas within which the time of travel to the well is less than or equal to two years but excluding WHPA-A.
  3. Area WHPA-C, being the surface and subsurface areas within which the time of travel to the well is less than or equal to five years but greater than two years.
  4. Area WHPA-D, being the surface and subsurface areas within which the time of travel to the well is less than or equal to twenty-five years but greater than five years.

Rule 52. The wellhead protection area for a wellhead associated with a type II or III system to which none of the regulations described in rule 51 apply, is the area created by combining all of the following areas:

  • Area WHPA-A, being the surface and subsurface area centred on the well with an outer boundary identified by a radius of 100 metres.
  • Area WHPA-B, being the surface and subsurface areas within which the time of travel to the well is less than or equal to two years but excluding WHPA-A.

Part V.5 – Delineation of WHPA-Q1 or WHPA-Q2

Rule 53. A wellhead protection area shall include all of the following areas if the relating well takes water from a subwatershed assigned a groundwater stress level of moderate or significant in accordance with Part III.4:

  1. Area WHPA-Q1, being the combined area that is the cone of influence of the well plus the whole of the cones of influence of all other wells that intersect that area and any surface water drainage area upstream of, and including, a losing reach of a stream that contributes a significant proportion of surface water to the wells.
  2. Area WHPA-Q2, being the area described in subrule (1) and any area outside the WHPA-Q1 where a future reduction in recharge would have a measureable impact on the municipal wells.

Rule 54. The model used in Part III to prepare the water budget for the local area that contains the well described in rule 53 shall be used to delineate WHPA (Wellhead Protection Area)-Q1 and WHPA-Q2.

Part VI – Delineation of vulnerable areas: surface water intake protection zones

Part VI.1 – General

Classification of intakes

Rule 55. Subject to rule 55.1, a surface water intake associated with a type I, II or III system shall be classified as a,

  1. type A intake if the intake or the planned intake is or would be located in a Great Lake;
  2. type B intake if the intake or the planned intake is or would be located in a connecting channel;
  3. type C intake if the intake or the planned intake is or would be located in a river and neither the direction nor velocity of the flow of the water at the intake is affected by a water impoundment structure; or
  4. type D intake if the intake is not described in subrule (1),(2) or (3).

Rule 55.1 The Director may, by written notice, classify an intake or planned intake associated with a type I, II or III system and the classification specified in the notice shall deem to be the classification for the intake or planned intake and any written notice given by the Director under this rule shall be included in the assessment report.

Identification of surface water bodies

Rule 56. Where these rules require the delineation of an IPZ-2 or an IPZ-3, the Water Virtual Flow – Seamless Provincial Data Set and the Water Poly Segment data layers housed in the Ontario Land Information Warehouse shall be used to identify the surface water bodies to be included in the IPZ-2 or IPZ-3, as the case may be.

Rule 57. Where there is no data in respect of the subwatershed in which the drinking water system related to the IPZ-2 or IPZ-3 is located in the Water Virtual Flow – Seamless Provincial Data Set data layer or in the Water Poly Segment data layer housed in the Ontario Land Information Warehouse, or where the data in the data layers is not sufficient to allow conclusions to be drawn with respect to the surface water bodies to be included in the IPZ-2 or IPZ-3, as the case may be, a computer based geographical information system shall be used to identify the surface water bodies to be included in the IPZ-2 or IPZ-3.

Part VI.2 - Area of surface water intake protection zones

Rule 58. A surface water intake protection zone for a surface water intake associated with a type I system or a type II or type III system to which O. Reg. 170/03 (Drinking Water Systems) made under the Safe Drinking Water Act, 2002, O. Reg. 318/08 (Transitional – Small Drinking Water Systems) made under the Health Protection and Promotion Act or O. Reg. 319/08 (Small Drinking Water Systems) made under the Health Protection and Promotion Act applies, is the area created by combining all of the following areas:

  1. Area IPZ-1, delineated in accordance with the rules in Part VI.3, as applicable.
  2. Area IPZ-2, delineated in accordance with the rules in Parts VI.4 and VI.6, as applicable.
  3. Area IPZ-3, delineated in accordance with the rules in Parts VI.5 and VI.6, as applicable.
  4. Area IPZ-Q, delineated in accordance with the rules in Part VI.7, as applicable.

Rule 59. A surface water intake protection zone for a surface water intake associated with a type II or type III system to which none of the regulations described in rule 58 apply, is the area created by combining all of the following areas:

  1. Area IPZ-1, delineated in accordance with the rules in Part VI.3.
  2. Area IPZ-Q, delineated in accordance with rules in Part VI.7, as applicable.

Rule 60. An area delineated in accordance with Parts VI.3 to Part VI.7 includes all surface and subsurface land, water and beds under the water within the boundary of the area delineated.

Part VI.3 - Delineation of IPZ-1

Rule 61. An area known as IPZ-1 shall be delineated in respect of each surface water intake associated with a drinking water system described in rules 58 and 59 and shall be composed of all of the following areas:

  1. A circle that has a radius of 1000 metres from the centre point of every intake that serves as the source or entry point of raw water supply for the system, if the intake is a,
    1. type A intake,
    2. type D intake, or
    3. a type C intake to which rule 63 applies.
  2. If the intake is a type B intake, a semi-circle that has a radius of 1000 metres extending upstream from the centre point of every intake that serves as the source or entry point of raw water supply for the system and a rectangle with a length of 2000 metres and a width of 100 metres extending downstream from the centre point.
  3. If the intake is a type C intake to which rule 63 does not apply, a semi-circle that has a radius of 200 metres extending upstream from the centre point of every intake that serves as the source or entry point of raw water supply for the system and a rectangle with a length of 400 metres and a width of 10 metres extending downstream from the centre point.

Rule 62. If the area delineated in accordance with rule 61 includes any land, the IPZ-1 shall only include a setback on the land that is the greater of,

  1. the area of land that drains into the surface water body measured from the high water mark and the area must not exceed 120 metres; and
  2. if a Conservation Authority Regulation Limit is in effect in the IPZ-1, only the area of land located within the Conservation Authority Regulation Limit that drains into a surface water body that is located in the IPZ-1.

Rule 63. The area of an IPZ-1 in a surface water body may be delineated in accordance with subrule 61(1) if the relating surface water body intake is a Type C intake and, having regard to the direction and flow velocity of the water at the intake, it would be reasonable to do soto protect the quality of the water that may enter the intake.

Rule 64. The area of an IPZ-1 in a surface water body may be modified to reflect local hydrodynamic conditions affecting flow if the modification is documented in the assessment report and a rationale is provided for the modification.

Part VI.4 - Delineation of IPZ-2

Rule 65. An area known as IPZ-2 shall be delineated for each surface water intake associated with a drinking water system described in rule 58, and shall be composed of all of the following areas:

  1. The area within each surface water body that may contribute water to the intake where the time of travel to the intake, subject to rule 66, is equal to or less than the time that is sufficient to allow the operator of the system to respond to a spill or other event thatmay impair the quality of the water at the intake and where the area abuts land, a setback that is the greater of,
    1. the area of land that drains into the surface water body measured from the high water mark and the area must not exceed 120 metres, and
    2. if a Conservation Authority Regulation Limit is in effect in the IPZ-2, only the area of land located within the Conservation Authority Regulation Limit that drains into a surface water body that is located in the IPZ-2.
  2. In respect of every stormwater management works that may contribute water to the intake, the area within the storm sewershed that contributes water to the works where the time of travel to the intake, subject to rule 66, is equal to or less than the time that is sufficient to allow the operator of the system to respond to a spill or other event thatmay impair the quality of the water at the intake.
  3. Removed.

Rule 66. For the purposes of subrules 65(1) and 65(2), where the time that is sufficient toallow the operator of the system to respond to an adverse condition in the quality of the surface water is less than two hours, the time of travel to the surface water body intake shall be deemed to be two hours.

Rule 67. Removed.

Part VI.5 - Delineation of IPZ-3

Rule 68. If, in respect of a drinking water system described in rule 58, modeling or other methods demonstrates that contaminants released during an extreme event may be transported to a type A and type B surface water intake or a type C or type D surface water intake located in Lake Nipissing, Lake Simcoe, Lake St. Clair or the Ottawa River, an area known as IPZ-3 shall be delineated and shall be composed of all of the following areas:

  1. Subject to rule 69, the area within each surface water body through which contaminants released during an extreme event may be transported to the intake.
  2. A setback on the land that abuts the portion of the surface water body that has been delineated in accordance with subrule (1), and this setback shall be the greater of,
    1. the area of land that drains into the surface water body measured from the high water mark and the area must not exceed 120 metres, and
    2. if a Conservation Authority Regulation Limit is in effect in the IPZ-3, only the area of land located within the Conservation Authority Regulation Limit that drains into a surface water body that is located in the IPZ-3.

Rule 69. The area delineated in accordance with subrule 68(1) shall not exceed the area within each surface water body that may contribute water to the intake during or as a result of an extreme event.

Rule 70. An area known as IPZ-3 shall be delineated for each type C and type D surface water intake that is not located in Lake Nippising, Lake Simcoe, Lake St. Clair or the Ottawa River, associated with a drinking water system described in rule 58 and shall be composed of all of the following areas:

  1. The area within each surface water body that may contribute water to the intake.
  2. A setback on the land that abuts the portion of the surface water body that has been delineated in accordance with subrule (1), and this setback shall be the greater of,
    1. the area of land that drains into the surface water body measured from the high water mark and the area must not exceed 120 metres, and
    2. if a Conservation Authority Regulation Limit is in effect in the IPZ-3, only the area of land located within the Conservation Authority Regulation Limit that drains into a surface water body that is located in the IPZ-3.

Rule 71. Removed.

Part VI.6 - Transport pathways and natural surface water features

Rule 72. Where an area that is an IPZ-2 or IPZ-3 includes a setback from a surface water body delineated in accordance with subrules 65(1), 68(2), 70(2) the area may be extended to include an area that contributes water to the IPZ-2 or IPZ-3, as the case may be, through a natural or anthropogenic transport pathway.

Rule 73. If an area of an IPZ-2 or IPZ-3 is extended under rule 72, the following factors shall be considered when determining the extended area:

  1. The hydrological and hydrogeological conditions of the area where the transport pathway is located.
  2. Where a transport pathway is anthropogenic in origin, the type and design of the pathway.
  3. In respect of an IPZ-2, the time of travel for water to enter into and pass through the transport pathway.

Rule 74. Despite rules 65, 66, and 72, an IPZ-2 shall not include an area of land or water that lies within the IPZ-1 that has been delineated for that surface water intake.

Rule 75. Despite rules 68, 70, and 72, an IPZ-3 shall not include an area of land or water that lies within the IPZ-1 or IPZ-2 that has been delineated for that surface water intake.

Part VI.7 - Delineation of IPZ-Q

Rule 76. A surface water intake protection zone shall include an area known as IPZ-Q if the relating intake takes water from a subwatershed assigned a surface water stress level of moderate or significant in accordance with Part III.4.

Rule 77. The boundary of the IPZ-Q described in rule 76 is the local area delineated in accordance with Part III.2 that relates to the surface water intake.

Rule 78. The models required to be used by Part III in the preparation of the water budget for the local area shall be used to delineate IPZ-Q.

Part VII – Vulnerability: highly vulnerable aquifers and wellhead protection areas

Part VII.1 - Highly vulnerable aquifers

Rule 79. A highly vulnerable aquifer shall be assigned a vulnerability score of 6.

Part VII.2 - Removed

Rule 80. Removed.

Rule 81. Removed.

Part VII.3 - Wellhead protection areas

Rule 82. A wellhead protection area shall be subdivided by the boundaries of the areas of groundwater vulnerability identified in accordance with Part IV rule 38.

Rule 83. The areas identified in accordance with rule 82 shall be assigned a vulnerability based upon their location within the areas identified in Part V rules 47 or 48 in accordance with,

  1. Table 2(a) and rule 84 where the groundwater vulnerability was determined by the use of a method listed in Part IV subrules 37(1) or 37(2);
  2. Table 2(b) and rule 84 where the groundwater vulnerability was determined by the use of a method listed in Part IV subrules 37(3) or 37(4); or
  3. an approach that is, in the opinion of the Director, comparable to those specified in subrules (1) and (2), if, in accordance with rule 15.1, a method that departs from the methods specified in rule 42 has been used, to determine time of travel to a wellhead.
Table 2(a): Wellhead Protection Area Vulnerability Scores - ISI or AVI
Groundwater Vulnerability Category for the Area Location Within a WHPA: WHPA-A  Location Within a WHPA: WHPA- B Location Within a WHPA: WHPA-C Location Within a WHPA: WHPA-C1 Location Within a WHPA: WHPA-D
High 10 10 8 8 6
Medium 10 8 6 6 4
Low 10 6 4 4 2
Table 2(b): Wellhead Protection Vulnerability Scores - SAAT or SWAT
Groundwater Vulnerability Category for the Area Location Within a WHPA: WHPA- A Location Within a WHPA: WHPA-B Location Within a WHPA: WHPA-C Location Within a WHPA: WHPA-C1 Location Within a WHPA: WHPA-D
High 10 10 8 8 6
Medium 10 8 6 6 4
Low 10 6 2 2 2

Rule 84. The areas identified in accordance with rule 82 that are located in WHPA-E shall be assigned a vulnerability score in accordance with the rules in Part VIII that apply to an IPZ-2.

Rule 85. Removed.

Part VIII – Vulnerability: surface water intake protection zones

Part VIII.1 - Vulnerability scores

Rule 86. A vulnerability score shall be assigned to each IPZ-1 and IPZ-2 associated with atype A, B, C or D intake and to each area of an IPZ-3 associated with a type C or type D intake.

Rule 87. The vulnerability score assigned to each IPZ-1, IPZ-2 and each area of an IPZ-3 associated with a type C or type D intake shall be calculated in accordance with the following formula,

B × C

Where,

B = the area vulnerability factor of the area of the surface water intake protection zone determined in accordance with rules 88 to 93; and

C = the source vulnerability factor of the surface water intake determined in accordance with rules 94 to 96.

Part VIII.2 - Area vulnerability factor

Rule 88. An IPZ-1 shall be assigned an area vulnerability factor of 10.

Rule 89. An IPZ-2 shall be assigned an area vulnerability factor that is not less than 7 and not more than 9 based on the vulnerability of the area where a higher factor corresponds to a higher vulnerability.

Rule 90. One or more area vulnerability factors that are not less than 1 and not greater than 9 shall be assigned to each area within an IPZ-3 associated with a type C or type D intake based on the vulnerability of the area within the IPZ-3 where a higher factor corresponds to a higher vulnerability.

Rule 91. An area vulnerability factor that is assigned to an IPZ-3 or an area within an IPZ-3 shall not be greater than the area vulnerability factor assigned to the IPZ-2 within the surface water intake protection zone.

Rule 92. The following shall be considered and documented in determining the area vulnerability factor of an IPZ-2 or of an area within an IPZ-3 for the purpose of rule 89 or 90 and an explanation shall be provided on how each affected the determination of the area vulnerability factor of that area:

  1. The percentage of the area of the IPZ-2 or IPZ-3, as the case may be, that is composed of land.
  2. The land cover, soil type, permeability of the land and the slope of any setbacks.
  3. The hydrological and hydrogeological conditions of the area where the transport pathway is located.
  4. In respect of an IPZ-3, the proximity of the area of the IPZ-3 to the intake.

Rule 93. An area vulnerability factor assigned for the purpose of rule 89 or 90 shall be expressed as a whole number.

Part VIII.3 - Source vulnerability factor

Rule 94. A source vulnerability factor shall be assigned to each surface water intake related toa type I, II or III system in accordance with Table 3 where a factor of 1 corresponds to a higher vulnerability.

Rule 95. The following shall be considered and documented in determining the source vulnerability factor of a surface water intake and an explanation shall be provided on how each affected the determination of the source vulnerability factor for the surface water intake:

  1. The depth of the intake from the top of the water surface.
  2. The distance of the intake from land.
  3. The history of water quality concerns at the surface water intake.
Table 3 - Source Vulnerability Factors
Intake Type Source Vulnerability Factor
type A intake 0.5 to 0.7
type B intake 0.7 to 0.9
type C intake 0.9 or 1
type D intake 0.8 to 1

Rule 95.1 If, in respect of a surface water intake described in rule 68 and having regard to the considerations set out in Rule 95 for assigning a source vulnerability factor for the intake, it is determined that the intake is in shallow waters, is in close proximity to the shoreline or there has been a history of water quality concerns at the surface water intake, the source vulnerability factor may, despite Table 3, vary from 0.5 to 1.

Rule 96. A source vulnerability factor assigned for the purpose of rule 94 may be expressed to one decimal place.

Part IX – Tier three water budgets (risk level assignment to local areas)

Part IX.1 Local area, evaluation of scenarios

Rule 97. Every local area delineated in accordance with rule 26 of Part III in respect of one or more planned or existing intakes that relate to one or more type I, II or III systems shall be assigned a risk level of significant, moderate or low by evaluating the surface water scenarios identified in Table 4A.

  1. Removed
  2. Removed

Rule 98. Every local area delineated in accordance with rule 27 of Part III in respect of one or more planned or existing wells that relate to one or more type I, II or III systems shall be assigned a risk level of significant, moderate or low by evaluating the groundwater scenarios identified in Table 4B.

  1. Removed
  2. Removed

Rule 99. For the purposes of Part IX.2, a reference to “other water uses" means,

  1. waste water assimilation,
  2. other water takings including agricultural, commercial and industrial water takings,
  3. navigation,
  4. recreation,
  5. aquatic habitat, and
  6. a provincially significant wetland.

Rule 100. For the purposes of evaluating the surface water scenarios A and B in Table 4A and the groundwater scenarios C and D in Table 4B, a tolerance level shall be assigned to the existing type I, II or III system to which the local area relates that is the subject of evaluation in accordance with the following:

  1. A tolerance level of high if the existing system is capable of meeting peak demand during all assessment periods.
  2. A tolerance level of low if sub-rule (1) does not apply to the existing system.

Part IX.2 Assignment of risk level

Rule 101. Removed.

Rule 102. Removed.

Rule 103. When evaluating the surface water scenarios in Table 4A in accordance with rule 97, the local area shall be assigned a risk level of significant if any of the following determinations are made:

  1. In respect of scenarios A and B, the tolerance level assigned to the drinking water system in accordance with rule 100 would be low.
  2. In respect of scenarios A, B, E1, E2, E3, F1, F2 and F3 it is determined in any of these scenarios that a period of time would exist where the quantity of water that can be taken from the surface water bodies in the local area would be insufficient to meet the associated demand of the intakes.
  3. In respect of scenario E5, it is determined that a period of time would exist where the difference between the allocated quantity of water and the planned quantity of water would result in a reduction to flows or levels of water thereby creating an unacceptable impact to other water uses.

Rule 104. When evaluating the groundwater scenarios in Table 4B in accordance with rule 98, the local area shall be assigned a risk level of significant if any of the following determinations are made:

  1. In respect of scenarios C and D, the tolerance level assigned to the drinking water system in accordance with rule 100 would be low.
  2. In respect of scenarios C, D, G1, G2, G3, H1, H2 and H3 it is determined in any of these scenarios that a period of time would exist where the quantity of water that can be taken from the groundwater system in the local area would be insufficient to meet the associated demand of the wells.
  3. In respect of scenario G5, it is determined that a period of time would exist where,
    1. the difference between the allocated quantity of water and the planned quantity of water would result in a reduction to flows or levels of water thereby creating an unacceptable impact to other water uses, or
    2. the difference between the allocated quantity of water and the planned quantity of water would result in a reduction in groundwater discharge to aquatic habitat that is classified as a cold water stream by an amount that is greater than,
      1. 20 percent of the existing estimated stream flow that is exceeded 80 per cent of the time (Qp80), or
      2. 20 percent of the existing estimated average monthly base flow of the stream.

Rule 105. When evaluating the surface water scenarios E4 and E5 in Table 4A, in accordance with rule 97, the local area shall be assigned a risk level of moderate, if a determination ismade that a period of time would exist where,

  1. in respect to scenario E4, the difference between the existing demand and the allocated quantity of water, would result in a reduction to flows or levels of water thereby creating a measurable and potentially unacceptable impact to other water uses, or
  2. in respect to scenario E5, the difference between the allocated quantity of water and the planned quantity of water would result in a reduction to flows or levels of water thereby creating a measurable and potentially unacceptable impact to other water uses.

Rule 106. When evaluating the groundwater scenarios G4 and G5 in Table 4B in accordance with rule 98, the local area shall be assigned a risk level of moderate, if a determination is made that a period of time would exist where,

  1. in respect to scenario G4:
    1. the difference between the existing demand and the allocated quantity ofwater, would result in a reduction to flows or levels of water thereby creating a measurable and potentially unacceptable impact to other water uses, or
    2. the difference between the existing demand and the allocated quantity ofwater, would result in a reduction in groundwater discharge to aquatic habitat that is classified as a cold water stream by an amount that is,
      1. at least 10 percent of the existing estimated stream flow that is exceeded 80 percent of the time (Qp80), or
      2. at least 10 percent of the existing estimated average monthly base flow of the stream.
  2. in respect to scenario G5:
    1. the difference between the allocated quantity of water and the planned quantity of water would result in a reduction to flows or levels of water thereby creating a measurable and potentially unacceptable impact to other water uses, or
    2. the difference between the allocated quantity of water and the planned quantity of water would result in a reduction in groundwater discharge to aquatic habitat that is classified as a cold water stream by an amount that is,
      1. at least 10 percent but not greater than 20 percent of the existing estimated stream flow that is exceeded 80 percent of the time (Qp80), or
      2. at least 10 percent but not greater than 20 percent of the existing estimated average monthly base flow of the stream.

Rule 107. If a local area is not assigned a risk level of significant or moderate in accordance with rule 103, 104, 105 or 106, a risk level of low shall be assigned to the local area.

Part IX.3 Uncertainty and sensitivity analysis:

Rule 108. After assigning a risk level to a local area, an uncertainty analysis shall be conducted that considers the following factors for the purpose of determining if the uncertainty underlying the risk assignment should be characterized as high or low:

  1. The distribution, variability, quality and relevance of the data used to evaluate the scenarios.
  2. The degree to which the methods and models used to evaluate the scenarios accurately reflects the hydrologic system of the local area for both steady state and transient conditions.
  3. The quality assurance and control procedures used in evaluating the scenarios.

Rule 109. Despite rules 105 and 106, a local area that is assigned a risk level of moderate in accordance with those rules shall be assigned a risk level of significant, if the uncertainty analysis conducted in accordance with rule 108 characterizes the uncertainty as high and a sensitivity analysis of the data used to prepare the water budget for the local area suggests that the risk level for the local area could be significant.

Table 4A (Rule 103) - Surface Water Risk Scenarios
Column 1: Scenario Column 2: Time Period Column 3: Land Cover of the Local Area Column 4: Quantity of Water De mand Column 5: Other Permitted Water Demand Column 6: Model Simulation Column 7: Determining Significant Risk Column 8: Determining Moderate Risk
A (Base) Climate data period Existing Existing Demand Existing Demand Long term daily flow using hourly climate and monthly pumping R 103(1) or
R 103(2)
N/A
B Two year or greater drought period Existing Existing Demand Existing Demand Long term daily flow using hourly climate and monthly pumping R 103(1) or
R 103(2)
N/A
E (1) Climate data period Recharge Reduction Allocated plus Planned Anticipated Demand Long term daily flow using hourly climate and monthly pumping R 103(2) N/A
E (2) Climate data period Existing Allocated plus Planned Existing Demand Long term daily flow using hourly climate and monthly pumping R 103(2) N/A
E (3) Climate data period Recharge Reduction Existing Demand Anticipated Demand Long term daily flow using hourly climate and monthly pumping R 103(2) N/A
E (4) Climate data period Existing Allocated Existing Demand Long term daily flow using hourly climate and monthly pumping N/A 105(1)R
E (5) Climate data period Existing Planned Existing Demand Long term daily flow using hourly climate and monthly pumping R 103(3) R 105 (2)
F (1) Two year or greater drought period Recharge Reduction Allocated plus Planned Anticipated Demand Long term daily flow using hourly climate and monthly pumping R 103(2) N/A
F (2) Two year or greater drought period Existing Allocated plus Planned Existing Demand Long term daily flow using hourly climate and monthly pumping R 103(2) N/A
F (3) Two year or greater drought period Recharge Reduction Existing Demand Anticipated Demand Long term daily flow using hourly climate and monthly pumping R 103(2) N/A
Table 4B (Rule 104) - Groundwater Risk Scenarios
Column 1: Scenario Column 2: Time Period Column 3: Land Cover of the Local Area Column 4: Quantity of Water De mand Column 5: Other Permitted Water Demand Column 6: Model Simulation Column 7: Determining Significant Risk Column 8: Determining Moderate Risk
C (Base) Climate data period Existing Existing Demand Existing Demand Steady state groundwater model should simulate water levels and flows using average annual recharge and monthly pumping R 104(1) or
R 104(2)
N/A
D Two year or greater drought period Existing Existing Demand Existing Demand Transient groundwater model should simulate water levels and flows using monthly recharge and monthly pumping R 104(1) or
R 104(2)
N/A
G (1) Climate data period Recharge Reduction Allocated plus Planned Anticipated Demand Steady state groundwater model should simulate water levels and flows using average annual recharge and monthly pumping R 104(2) N/A
G (2) Climate data period Existing Allocated plus Planned Existing Demand Steady state groundwater model should simulate water levels and flows using average annual recharge and monthly pumping R 104(2) N/A
G (3) Climate data period Recharge Reduction Existing Demand Anticipated Demand Steady state groundwater model should simulate water levels and flows using average annual recharge and monthly pumping R 104(2) N/A
G (4) Climate data period Existing Allocated Existing Demand Steady state groundwater model should simulate water levels and flows using average annual recharge and monthly pumping N/A 106(1)R
G (5) Climate data period Existing Planned Existing Demand Steady state groundwater model should simulate water levels and flows using average annual recharge and monthly pumping R 104(3) R 106(2)
H (1) Two year or greater drought period Recharge Reduction Allocated plus Planned Anticipated Demand Transient groundwater model should simulate water levels and flows using monthly recharge and monthly pumping R 104(2) N/A
H (2) Two year or greater drought period Existing Allocated plus Planned Existing Demand Transient groundwater model should simulate water levels and flows using monthly recharge and monthly pumping R 104(2) N/A
H (3) Two year or greater drought period Recharge Reduction Existing Demand Anticipated Demand Transient groundwater model should simulate water levels and flows using monthly recharge and monthly pumping R 104(2) N/A

Explanatory notes on Table 4A and 4B

  1. Column 1 sets out the name of the scenario.
  2. Column 2 sets out the period of time that each scenario is required to evaluate. The term “climate data period” means the historical period for which climate and stream flow data are available for.
  3. Column 3 sets out how “land cover”, as defined in sub-rule 1(1), should be considered when evaluating a scenario. “Existing” indicates that the scenario should consider the existing amount and extent of impervious and non-impervious areas in the local area. “Recharge Reduction” indicates the scenario should consider the amount and extent of impervious and non-impervious areas in the local area assuming development occurred as projected in the municipal official plan or in accordance with class environmental assessments.
  4. Column 4 sets out the “Quantity of Water” or “Demand” as defined in sub-rule 1(1) that should be determined and assessed for each scenario. “Existing Demand” means the quantity of water determined to be currently taken from an existing surface water intake or an existing well during the study period. “Allocated” means, in respect of an existing surface water intake or an existing well, the existing demand of the intake or well plus any additional quantity of water that would have to be taken by the intake or well to meet its committed demand, up to the maximum quantity of water that can lawfully be taken by the intake or well. “Planned” means in respect of an existing surface water intake or existing well, any amount of water that meets the definition of a planned system in O. Reg. 287/07 and any amount of water that is needed to meet a committed demand above the maximum quantity of water that can lawfully be taken by the intake or well, or, in respect of a new planned surface water intake or planned well, any amount of water that meets the definition of a planned system in O. Reg. 287/07.
  5. Column 5 sets out how other water takings in the local area, as identified under sub-rule 99(b), should be considered when evaluating a scenario. However, for the purposes of the column, only water takers that are required to obtain a permit to take water under the Ontario Water Resources Act should be considered. “Existing” means determining for each permitted water taker the actual or estimated amounts of consumptive water taking. “Anticipated” means determining for those permitted water takers, where possible, the estimated amounts of consumptive water taking that may likely, or will occur in the near future.
  6. Column 6 sets out the modelling mode and minimum climate and pumping time periods for the surface and groundwater models as defined in sub-rule 1(1). For surface water, the model should simulate long term daily flow using hourly climate and monthly pumping inputs. For groundwater, the model should simulate both steady state (using average annual recharge and monthly pumping) and transient (using monthly recharge and monthly pumping) conditions.
  7. Column 7 identifies the rules that set out the determinations for a risk level of “significant” for the corresponding scenario. Column 8 identifies the rules that set out the determinations for a risk level of “moderate” for the corresponding scenario. Where, after evaluating a scenario, no determination has been made for that scenario in accordance with a rule referred to in Column 7 or 8, the local area that is the subject of evaluation must be given a risk level of low.

Part X – Drinking water threats: water quantity

Part X.1 – Listing of drinking water threats

Rule 110. The activities prescribed to be drinking water threats for a vulnerable area in paragraphs 19 and 20 of subsection 1.1(1) of O. Reg. 287/07 (General) may be collectively listed in the assessment report as “the activities prescribed to be drinking water threats in paragraphs 19 and 20 of subsection 1.1(1) of O. Reg. 287/07 (General)”.

Part X.2 – Listing of significant and moderate drinking water threats

 Rule 111. An activity listed in Column 1 of Table 5 is a significant drinking water threat in the circumstances and the areas within a vulnerable area set out opposite to the activity in Columns 2 and 3 respectively.

Rule 112. An activity listed in Column 1 of Table 5 is a moderate drinking water threat in the circumstances and the areas within a vulnerable area set out opposite to the activity in Columns 2 and 4 respectively.

Rule 113. For the purposes of Table 5, “existing taking” in respect of an activity means the historical average annual quantity of water taken by that activity.

Table 5 - Water Quantity Drinking Water Threats and Significant Drinking Water Threats
 Activity (Drinking Water Threat)  Circumstance Area where Activity is a Significant Drinking Water Threat Area where Activity is a Moderate Drinking Water Threat
An activity that takes water from an aquifer or a surface water body without returning the water taken to the same aquifer or surface water body.  Reference Number 1.
  1. An existing taking, an increase to an existing taking or a new taking.
  2. The water is or would be taken from within an IPZ- Q.
IPZ-Q where the water is or would be taken if the area relates to one or more surface water intakes and the local area was assessed to have a risk level of significant in accordance with Part IX. IPZ-Q where the water is or would be taken if the area relates to one or more surface water intakes and the local area was assessed to have a risk level of moderate in accordance with Part IX.
An activity that takes water from an aquifer or a surface water body without returning the water taken to the same aquifer or surface water body.

Reference Number 2.

  1. An existing taking, an increase to an existing taking or a new taking.
  2. The water is or would be taken from within a WHPA-Q1.
WHPA-Q1 where the water is or would be taken if the area relates to one or more wells and the local area was assessed to have a risk level of significant in accordance with Part IX. WHPA-Q1 where the water is or would be taken if the area relates to one or more wells and the local area was assessed to have a risk level of moderate in accordance with Part IX.
An activity that takes water from an aquifer or a surface water body without returning the water taken to the same aquifer or surface water body.

Reference Number 3.

  1. An increase to an existing taking or a new taking.
  2. Section 34 of the Ontario Water Resources Act requires a permit to take water in respect of the increase or new taking.
  3. The water is or would be taken from within an IPZ- Q.
  4. Despite the local area from which the water is or would be taken having been assessed for the purposes of the latest assessment report to have a risk level of moderate in accordance with Part IX, the local area would be assessed to have a risk level of significant if the increase to the existing taking or the new taking were factored into the risk level assessment.
IPZ-Q where the water is or would be taken if the area relates to one or more surface water intakes and the local area was assessed to have a risk level of moderate in accordance with Part IX. N/A
An activity that takes water from an aquifer or a surface water body without returning the water taken to the same aquifer or surface water body.

Reference Number 4.

  1. An increase to an existing taking or a new taking.
  2. The water is or would be taken from within a WHPA-Q1.
  3. Section 34 of the Ontario Water Resources Act requires a permit to take water in respect of the increase or new taking.
  4. Despite the local area from which the water is or would be taken having been assessed for the purposes of the latest assessment report to have a risk level of moderate in accordance with Part IX, the local area would be assessed to have a risk level of significant if the increase to the existing taking or the new taking were factored into the risk level assessment.
WHPA-Q1 where the water is or would be taken if the area relates to one or more wells and the local area was assessed to have a risk level of moderate in accordance with Part IX. N/A
An activity that reduces recharge to an aquifer.

Reference Number 5.

  1. An existing activity, a modified activity or a new activity.
  2. The activity is or would be wholly or partly located within an IPZ-Q.
IPZ-Q where the water is or would be taken if the area relates to one or more surface water intakes and the local area was assessed to have a risk level of significant in accordance with Part IX. IPZ-Q where the water is or would be taken if the area relates to one or more surface water intakes and the local area was assessed to have a risk level of moderate in accordance with Part IX.
An activity that reduces recharge to an aquifer.

Reference Number 6.

  1. An existing activity, a modified activity or a new activity.
  2. The activity is or would be wholly or partly located within a WHPA-Q2.
WHPA-Q2 where the water is or would be taken if the area relates to one or more wells and the local area was assessed to have a risk level of significant in accordance with Part IX. WHPA-Q2 the water is or would be taken if the area relates to one or more wells and the local area was assessed to have a risk level of moderate in accordance with Part IX.
An activity that reduces recharge to an aquifer.

Reference Number 7.

  1. A modified activity or a new activity.
  2. The activity is or would be wholly or partly located within an IPZ-Q.
  3. Despite the local area from which the water is or would be taken having been assessed for the purposes of the latest assessment report to have a risk level of moderate in accordance with Part IX, the local area would be assessed to have a risk level of significant if the modified activity were factored into the risk level assessment.
IPZ-Q where the water is or would be taken if the area relates to one or more surface water intakes and the local area was assessed to have a risk level of moderate in accordance with Part IX. N/A
An activity that reduces recharge to an aquifer.

Reference Number 8.

  1. A modified activity or a new activity.
  2. The activity is or would be wholly or partly located within a WHPA-Q2.
  3. Despite the local area from which the water is or would be taken having been assessed for the purposes of the latest assessment report to have a risk level of moderate in accordance with Part IX, the local area would be assessed to have a risk level of significant if the modified activity were factored into the risk level assessment. In effect December 2, 2013
WHPA-Q2 where the water is or would be taken if the area relates to one or more wells and the local area was assessed to have a risk level of moderate in accordance with Part IX. N/A

Part XI – Drinking water threats: water quality

Part XI.1 - Describing drinking water issues

Rule 114. If the source protection committee is aware of one of the following, the committee shall describe it as a drinking water issue under clause 15(2)(f) of the Act in accordance with rule 115:

  1. The presence of a parameter in water at a surface water intake or in a well, including a monitoring location related to a drinking water system to which clause 15(2)(e) of the Act applies, if the parameter is listed in Schedule 1, 2 or 3 of the Ontario Drinking Water Quality Standards or Table 4 of the Technical Support Document for Ontario Drinking Water Standards, Objectives and Guidelines and,
    1. the parameter is present at a concentration that may result in the deterioration of the quality of the water for use as a source of drinking water, or
    2. there is a trend of increasing concentrations of the parameter at the surface water intake, well or monitoring location and a continuation of that trend would result in the deterioration of the quality of the water for use as a source of drinking water.
  2. The presence of a pathogen in water at a surface water intake or in a well, including a monitoring location, related to a drinking water system to which clause 15(2)(e) of the Act does apply, if a microbial risk assessment undertaken in respect of the pathogen indicates that,
    1. the pathogen is present at a concentration that may result in the deterioration of the quality of the water for use as a source of drinking water, or
    2. there is a trend of increasing concentrations of the pathogen at the surface water intake or well and a continuation of that trend would result in the deterioration of the quality of the water for use as a source of drinking water.
  3. In respect of drinking water systems in the vulnerable area that are not mentioned in clause 15(2)(e) of the Act, there is evidence of the widespread presence of a parameter listed in Schedule 2 or 3 of the Ontario Drinking Water Quality Standards or Table 4 of the Technical Support Document for Ontario Drinking Water Standards, Objectives and Guidelines at surface water intakes or in wells, including monitoring locations, related to those systems, and
    1. the parameter is present at a concentration that may result in the deterioration of the water for use as a source of drinking water, or
    2. there is a trend of increasing concentrations of the parameter at the intake, well or monitoring location and a continuation of that trend would result in the deterioration of the quality of the water for use as a source of drinking water.

Rule 115. Only in respect of a drinking water issue identified in accordance with rule 114, where the drinking water issue is the result of, or partially the result of, anthropogenic causes, the description of the drinking water issue shall include the following information:

  1. The parameter or pathogen concerned.
  2. The surface water intake, well or monitoring location at which the presence of the parameter or pathogen has occurred.
  3. The area within a vulnerable area where activities, conditions that result from past activities, and naturally occurring conditions may contribute to the parameter or pathogen and this area shall be identified as the “issue contributing area”; and
  4. The identification of the drinking water threats listed in accordance with rules 118, 119 or 126 that contribute or may contribute to the parameter or pathogen of concern.

Rule 115.1 In respect of a drinking water issue that is not described under rule 115, the description of the drinking water issue shall include,

  1. the parameter or pathogen concerned; and
  2. an explanation of the nature of the issue and the possible causes of the issue.

Rule 116. If the information specified by subrules 115(3) or (4) cannot be readily ascertained, the assessment report shall include,

  1. a plan that includes a work schedule for ascertaining the information specified by those subrules, including any additional work that must be carried out as a result of ascertaining this information; and
  2. if, after completing the work the source protection committee becomes aware that the assessment report is no longer accurate or complete, an estimate of the date by which the source protection committee expects an updated assessment report would be submitted to the Director under section 19 of the Act.

Rule 117. If the source protection committee is of the opinion that areas, activities or conditions referred to in subrules 115(3) or (4) are located outside the boundaries of the source protection area, the description of the drinking water issue shall include this information and shall identify the source protection area in which the source protection committee believes such areas and activities or conditions may be located.

Part XI.2 - Listing drinking water threats - activities

Activities prescribed to be drinking water threats

Rule 118. The activities prescribed to be drinking water threats for a vulnerable area in paragraphs 1 through 18 and paragraph 21 of subsection 1.1(1) of O. Reg. 287/07 (General) may be collectively listed in the assessment report as “the activities prescribed to be drinking water threats in paragraphs 1 through 18 and paragraph 21 of subsection 1.1(1) of O. Reg. 287/07 (General)”.

Rule 118.1 When identifying the circumstances in which an activity is or would be asignificant drinking water threat, a moderate drinking water threat, or a low drinking water threat in accordance with paragraphs 3 to 5 of subsection 13(1) of O. Reg. 287/07 (General), the report may refer to the applicable parts of the Table of Drinking Water Threats that sets out the set of circumstances that makes an activity a significant, moderate or low drinking water threat.

Other activities

Rule 119. In addition to activities prescribed to be drinking water threats in paragraphs 1 through 18 and paragraph 21 of subsection 1.1(1) of O. Reg. 287/07 (General), an activity shall be listed as a drinking water threat for a vulnerable area if,

  1. the activity has been identified by the source protection committee as an activity that may be a drinking water threat; and
  2. information provided by the Director indicates that,
    1. the chemical hazard rating of the activity is greater than 4; or
    2. the pathogen hazard rating of the activity is greater than 4.
  3. Removed.

Rule 120. The chemical hazard rating of an activity that is not prescribed to be a drinking water threat under O. Reg. 287/07 (General) shall be a rating that in the opinion of the Director reflects the hazard presented by the chemical parameter associated with the activity, if any, considering the following factors:

  1. Toxicity of the parameter.
  2. Environmental fate of the parameter.
  3. Quantity of the parameter.
  4. Method of release of the parameter to the natural environment.
  5. Type of vulnerable area in which the activity is or would be located.

Rule 121. The pathogen hazard rating of an activity that is not prescribed to be a drinking water threat under O. Reg. 287/07 (General) shall be a rating that in the opinion of the Director reflects the hazard presented by pathogens associated with the activity, if any, considering the following factors:

  1. The frequency of the presence of pathogens that may be associated with the activity.
  2. Method of release of the pathogen to the natural environment.
  3. Type of vulnerable area in which the activity is or would be located.

Rule 122. The risk score of an area within a vulnerable area in respect of an activity that is not listed in the Tables of Drinking Water Threats shall be calculated in accordance with the following formula:

A × B

Where,

A = the chemical hazard rating or pathogen hazard rating of the activity determined in accordance with rule 120 or 121, as the case may be; and

B = the vulnerability of the score of the area within the vulnerable area determined in accordance with Part VII or Part VIII, as the case may be.

Rule 123. Removed.

Rule 124. Removed.

Rule 125. If an activity that is not prescribed to be a drinking water threat under O. Reg. 287/07 (General) is listed as an activity that is or would be a drinking water threat, the following information shall be provided in a table format:

  1. The circumstances that make the activity a drinking water threat shall be specified opposite the activity.
  2. The hazard rating of the activity determined in accordance with rule 120 or 121 or both, as the case may be, shall be listed opposite the activity.

Part XI.3 - Listing drinking water threats - conditions

Listing Conditions that result from past activities

Rule 126. If the source protection committee is aware of one of the following conditions that results from past activities, the committee shall list it as a drinking water threat under clause 15(2)(g)(ii) of the Act:

  1. The presence of a non-aqueous phase liquid in groundwater in a highly vulnerable aquifer, significant groundwater recharge area or wellhead protection area.
  2. The presence of a single mass of more than 100 litres of one or more dense non- aqueous phase liquids in surface water in a surface water intake protection zone.
  3. The presence of a contaminant in groundwater in a highly vulnerable aquifer, significant groundwater recharge area or a wellhead protection area, if the contaminant is listed in Table 2 of the Soil, Ground Water and Sediment Standards, is present at a concentration that exceeds the potable groundwater standard set out for the contaminant in that Table, and the presence of the contaminant in groundwater could result in the deterioration of the groundwater for use as a source of drinking water.
  4. The presence of a contaminant in surface soil in a surface water intake protection zone if, the contaminant is listed in Table 4 of the Soil, Ground Water and Sediment Standards is present at a concentration that exceeds the surface soil standard for industrial/commercial/community property use set out for the contaminant in thatTable and the presence of the contaminant in surface soil could result in the deterioration of the surface water for use as a source of drinking water.
  5. The presence of a contaminant in sediment in an intake protection zone, if the contaminant is listed in Table 1 of the Soil, Ground Water and Sediment Standards and is present at a concentration that exceeds the sediment standard set out for the contaminant in that Table, and the presence of the contaminant in sediment could result in the deterioration of the surface water for use as a source of drinking water.
  6. The presence of a contaminant in groundwater that is discharging into an intake protection zone, if the contaminant is listed in Table 2 of the Soil, Ground Water and Sediment Standards, the concentration of the contaminant exceeds the potable groundwater standard set out for that contaminant in the Table, and the presence of the contaminant in groundwater could result in the deterioration of the surface water for use as a source of drinking water.

Part XI.4 - Identifying areas for significant, moderate and low drinking water threats - activities

Significant drinking water threats

Rule 127. An activity listed as a drinking water threat in accordance with rule 118 is or would be a significant drinking water threat in an area set out opposite to the activity in column 3 of Table 1 or Table 2 of the Tables of Drinking Water Threats if the area has a vulnerability score set out in column 4 of the respective Table and the set of circumstances set out in a cell of column 2 of the respective Table opposite to the area apply to the activity.

Rule 128. An activity listed as a drinking water threat in accordance with rule 118 is or would be a significant drinking water threat if rule 127 does not apply and the following apply:

  1. The chemical hazard rating or pathogen hazard rating for the chemical parameter or pathogen associated with the circumstances under which the activity is or will be engaged in, determined in accordance with rule 120 or 121, is greater than 4.
  2. The area within a vulnerable area where the activity is or will be engaged in has arisk score calculated in accordance with rule 122 that is equal to or greater than 80.

Rule 129. An activity listed as a drinking water threat in accordance with rule 119 is or would be a significant drinking water threat in an area within a vulnerable area that has a risk score in respect of the activity calculated in accordance with rule 122 that is equal to or greater than 80.

Rule 130. An activity listed as a drinking water threat in accordance with rule 118 or 119 is or would be a significant drinking water threat in a surface water intake protection zone associated with a surface water intake to which rule 68 applies at the location where the activity is or would be engaged in, if modeling or another method demonstrates that a release of a chemical parameter or pathogen from the activity or the proposed activity would be transported through the surface water intake protection zone to the intake and result in the deterioration of the water for use as a source of drinking water for the intake.

Rule 131. Despite anything else in these rules, an activity is or would be a significant drinking water threat if,

  1. the activity is associated with a drinking water issue described in subrule 114(1) or (2);
  2. the activity is identified as a drinking water threat in accordance with subrule 115(4);
  3. the activity is located in an issue contributing area identified in accordance with subrule 115(3); and
  4. the circumstances described in rule 131.1 apply to the activity.

Rule 131.1 The circumstances for the purposes of subrule 131(4) are,

  1. if the activity is listed as a drinking water threat in accordance with rule 118, a set of circumstances set out in an applicable cell in Column 2 of the Table of Drinking Water Threats that contribute or may contribute to the drinking water issue mentioned in subrule 131(1); or
  2. if the activity is listed as a drinking water threat in accordance with rule 119, the circumstances for the activity specified in accordance with rule 125 that contribute or may contribute to the drinking water issue mentioned in subrule 131(1).

Moderate drinking water threats

Rule 132. An activity listed as a drinking water threat in accordance with rule 118 is or would be a moderate drinking water threat in an area set out opposite to the activity in column 3 of Table 1 or Table 2 of the Tables of Drinking Water if the area has a vulnerability score set out in column 5 of the respective Table and all of the circumstances set out in column 2 of the respective Table opposite to the area apply to the activity.

Rule 133. An activity listed in accordance with rule 118 is or would be a moderate drinking water threat if rule 132 does not apply and the following apply:

  1. The chemical hazard rating or pathogen hazard rating for the chemical parameter or pathogen associated with the circumstances under which the activity is or will be engaged in, determined in accordance with rule 120 or 121, is greater than 4.
  2. The area within a vulnerable area in which the activity is or will be engaged in has arisk score calculated in accordance with rule 122 that is equal to or greater than 60 but less than 80.

Rule 134. An activity listed as a drinking water threat in accordance with rule 119 is or would be a moderate drinking water threat in an area within a vulnerable area that has a risk score in respect of the activity calculated in accordance with rule 122 equal to or greater than 60 but less than 80.

Rule 134.1 Despite anything else in these rules an activity is or would be a moderate drinking water threat if,

  1. The activity is not identified in accordance with rules 127 to 131.1 as an activity that is or would be a significant drinking water threat;
  2. the activity is associated with a drinking water issue described in subrule 114(3);
  3. the activity is identified as a drinking water threat in accordance with subrule 115(4);
  4. the activity is located in an issue contributing area identified in accordance withsubrule 115(3); and
  5. the circumstances described in rule 134.2 apply to the activity.

Rule 134.2 The circumstances for the purposes of subrule 134.1(5) are,

  1. if the activity is listed as a drinking water threat in accordance with rule 118, a set of circumstances set out in an applicable cell in Column 2 of the Table of Drinking Water Threats that contribute or may contribute to the drinking issue mentioned in subrule 134.1(1); or
  2. if the activity is listed as a drinking water threat in accordance with rule 119, the circumstances for the activity specified in accordance with rule 125 that contribute or may contribute to the drinking water issue mentioned in subrule 134.1(1).

Low drinking water threats

Rule 135. An activity listed as a drinking water threat in accordance with rule 118 is or would be a low drinking water threat in an area set out opposite to the activity in column 3 of Table 1 or Table 2 of the Tables of Drinking Water if the area has a vulnerability score set out in column 6 of the respective Table and all of the circumstances set out in column 2 of the respective Table opposite to the area apply to the activity.

Rule 136. An activity listed as a drinking water threat in accordance with rule 118 is a low drinking water threat if rule 135 does not apply and the following apply:

  1. The chemical hazard rating or pathogen hazard rating for the chemical parameter or pathogen associated with the circumstances under which the activity is or will be engaged in, determined in accordance with rule 120 or 121, is greater than 4.
  2. The area within a vulnerable area in which the activity is or will be engaged in has arisk score calculated in accordance with rule 122 that is greater than 40 but less than 60.

Rule 137. An activity listed as a drinking water threat in accordance with rule 119 is or would be a low drinking water threat in an area within a vulnerable area that has a risk score in respect of the activity calculated in accordance with rule 122 to be greater than 40 but less than 60.

Part XI.5 - Identifying areas for significant, moderate and low drinking water threats - conditions

Rule 138. The risk score of an area in respect of a condition that results from a past activity shall be calculated in accordance with the following formula:

A × B

Where,

A = the hazard rating of the condition;

B = the vulnerability of the score of the area determined in accordance with Part VII or VIII, as the case may be.

Rule 139. For the purpose of rule 138, the hazard rating of a condition that results from a past activity is,

  1. if there is evidence that the condition is causing off site contamination that has the potential to deteriorate the quality of water of the aquifer drinking water source or the surface water drinking water source, the hazard rating is 10;
  2. if the condition is on a property where a well, intake or monitoring location related to a drinking water system to which clause 15(2)(e) of the Act applies is located, the hazard rating is 10; and
  3. if subrules (1) or (2) do not apply to the condition, the hazard rating is 6.

Identifying areas for significant conditions

Rule 140. An area within a vulnerable area is an area where a condition that results from a past activity listed in accordance with rule 126 is a significant drinking water threat if the risk score of the area in respect of the condition is equal to or greater than 80.

Rule 140.1 Removed.

Rule 141. Despite anything else in these rules, a condition that results from a past activity isa significant drinking water threat if,

  1. the condition is associated with a drinking water issue described in subrule 114(1) or (2);
  2. the condition is identified as a drinking water threat in accordance with subrule 115(4);
  3. the condition is located in an issue contributing area identified in accordance withsubrule 115(3); and
  4. there is evidence that the condition is causing off-site contamination that has the potential to deteriorate the quality of water of the aquifer drinking water source or the surface water drinking water source or the condition is on the property where the surface water intake, well or monitoring location identified in accordance with subrule 115(2) is located.

Identifying areas for moderate conditions

Rule 142. Subject to rule 141, an area within a vulnerable area is an area where a condition that results from a past activity listed in accordance with rule 126 is a moderate drinking water threat if the risk score of the area in respect of the condition is equal to or greater than 60 but less than 80.

Rule 142.1 Despite anything else in these rules a condition that results from a past activity isa moderate drinking water threat if:

  1. The condition is not identified in accordance with rules 140 and 141 as a condition that is a significant drinking water threat;
  2. the condition is associated with a drinking water issue described in subrule 114(3);
  3. the condition is identified as a drinking water threat in accordance with subrule 115(4); and
  4. the activity is located in an issue contributing area identified in accordance withsubrule 115(3).

Identifying areas for low conditions

Rule 143. Subject to rule 141, an area within a vulnerable area is an area where a condition that results from a past activity listed in accordance with rule 126 is a low drinking water threat if the risk score of the area in respect of the condition is greater than 40 but less than 60.

Changes to the tables Of drinking water threats

The following changes have been made to the Tables of Drinking Water Threats:

  1. Within the table of contents the following changes have been made to the short form names:
    1. Application of NASM (including Treated Septage) has changed to Application of NASM or Biosolids to Land.
    2. Application of Untreated Septage has changed to Application of Hauled Sewage to Land.
    3. Sewage System or Sewage Works - Discharge of Untreated Stormwater has changed to Sewage System or Sewage Works - Discharge from a Stormwater Management Facility.
    4. Septic System has changed to Onsite Sewage Systems.
    5. Sewage System or Sewage Works - Storage of Sewage (e.g. Treatment Plant Tanks) has changed to Sewage System or Sewage Works - Sewage WorksStorage - Treatment or Holding Tanks.
  2. All references to Significant Groundwater Recharge Areas have been removed. Activities are already captured as moderate and low risks through the overlapping Highly Vulnerable Aquifer zones.
  3. For above grade, or partially below grade, handling and storage of fuel the hazard rating for surface water was calculated using a Release and Impact Modifier of 8. The tables have been amended to reflect a release and impact modifier of 10. As a result, the activity would be identified as a significant drinking water threat in more areas including intake protection zones scoring 9 or 10 and volumes of 250L or more. The reference numbers for the circumstances are:

    Circumstances 112-121, 132-141, 152-161, 172-181, 1289-1298, 1309-1328,
    1339-1358, 1369-1388, 1399-1408

  4. The term “a dairy producer” has been removed from the following circumstances:

    Circumstances 1965, 1967 and 1970

  5. The following circumstances have been removed from the tables for septic systems and holding tanks, eliminating both sodium and chloride as chemicals of concern:

    Circumstances 696, 700, 702, 706, 708, 712, 714 and 718